Jura Capresso Impressa 68193 User Manual

CAPRESSO  
Impressa S9  
One Touch  
Fully Automatic  
Coffee & Espresso Center  
with Clearyl Water Care System  
Operating Instructions  
and Warranty  
Customer Service 1-800-220-5701  
Impressa S9 One Touch  
Notice: This machine has a 3-prong grounded plug.  
To reduce the risk of electrical shock, this plug will fit in an  
outlet only one way. If the plug does not fit in the outlet,  
contact a qualified electrician. DO NOT modify the plug in  
any way.  
JURA-CAPRESSO  
Jura was founded in 1931 in Switzerland. Capresso was  
founded in 1994 in the USA. Both companies have joined  
forces in the US to bring you the finest Fully Automatic  
Coffee Centers available anywhere. With innovative and  
user-friendly features, high quality materials, clear instruc-  
tions and superb customer service, we are sure you will  
experience the best coffee, espresso, cappuccino or latte  
you have ever had. We hope you will enjoy your new Fully  
Automatic Coffee Center and will recommend it to your  
friends. For more information about our products visit our  
CAUTION  
This appliance is for household use. Any servicing other than  
cleaning and user maintenance should be performed by an  
authorized service representative.  
• Do not immerse base in water or try to disassemble.  
To reduce the risk of fire or electric shock, do not remove  
the base. No user serviceable parts inside. Repair should  
be done by authorized service personnel only.  
• Check voltage to be sure that the voltage indicated on the  
name plate agrees with your voltage.  
Customer Service  
1-800-220-5701  
• Never use warm or hot water to fill the water container!  
Use cold water only!  
• Keep your hands and the cord away from hot parts of the  
appliance during operation.  
• Never clean with scouring powders or hard implements.  
Mon-Thu 9AM – 9PM • Fri 9AM – 8PM • Sat 9AM – 5PM  
Eastern Standard Time.  
Jura-Capresso  
81 Ruckman Road, Closter, NJ 07624  
201-767-3999 • Fax: 201-767-9684  
3.  
FIG. 1  
1. Height-Adjustable Dual Coffee Spout  
2. Operating Display (Fig.2)  
3. Removable Water Tank  
4. Low Water Flotation Device (inside)  
5. Clearyl Water Care Cartridge  
(Not Installed)  
10  
11  
12  
13  
14  
15  
15a  
16  
17  
18  
19  
9
8
7
6
5
4
3
6. Lid for Water Tank  
7. Holder for Clearyl Water Cartridge  
8. Bean Aroma Protection Lid  
9. Cover for Bean Container  
10. Lid for Ground Coffee Funnel  
11. Opening for Ground Coffee  
12. Warming Plate  
13. Auto Cappuccino System (Fig. 3)  
14. Hot Water Spout  
15. Steam Nozzle  
15a. frothXpress system (Fig. 15 through 17a)  
with thermal milk container attached  
16. Used Coffee Container  
17. Cup platform  
18. Removable Drawer/Used Water Tray  
19. Cover for Rotary Dial and  
A La Carte Button (Fig. 3A)  
2
1
FIG. 1b  
FIG. 1a  
a. Scoop  
d
a
c
b. Cleaning tablets  
c. Water indicator  
d. Clearyl filter  
Main Power Switch  
b
4.  
Operating Display  
FIG. 2  
Auto Cappuccino System  
FIG. 3  
FIG. 3A  
FIG. 4  
COFFEE  
READY  
A
B
N
O
3.1  
3.2  
3.5  
3.3  
3.4  
E
P
3.6  
3.7  
C
D
F
Dual  
Coffee  
Spouts  
Hot  
Water  
Spout  
Q
G
Display Dialog System  
3.1 Hot Water Portion symbol  
N.  
O.  
P.  
A.  
B.  
C.  
D.  
E.  
F.  
A La Carte Button  
ON/OFF Button  
Ground Coffee Button  
Rotary Dial w/push button  
3.2 Milk Portion symbol  
3.3 Selector Dial with push button  
3.4 Hot Water symbol  
1-CUP Espresso Button  
1-CUP Coffee Button  
RINSE Button  
Q.  
Service Cover  
(do not remove)  
3.5 Milk symbol  
2-CUP Espresso Button  
2-CUP Coffee Button  
3.6 Cappuccino button  
3.7 Latte Macchiato button  
G.  
5.  
FIG. 5  
FIG. 6  
FIG. 7  
FIG. 8  
FIG. 9  
FIG. 10  
FIG. 11  
FIG. 12  
FIG. 13  
Extension rod  
6.  
FIG. 14a  
FIG. 14b  
FIG. 15  
Black fitting  
Transparent  
fitting  
Coffee  
spout  
Milk  
hose  
Stainless steel rod  
Milk/ Steam  
spout  
FIG. 16  
FIG. 17  
FIG. 17a  
Siphoning  
with  
flexible  
hose  
venting tip  
chrome  
face plate  
Frothing range  
Steam only  
no siphoning  
DIAL  
Steaming range  
7.  
FIG. 19  
FIG. 20  
FIG. 21  
FIG. 18  
FIG. 22  
FIG. 23  
FIG. 24  
FIG. 25  
8.  
TABLE OF CONTENTS  
PAGE  
PAGE  
8a. Turning the Machine Off / Rinsing............................. 16  
Important Safeguards / Jura Capresso .....................  
2
Drawings ....................................................................4-8  
Important / Battery Back-up................................... 11  
Product Warranty Registration................................... 11  
Operating Instructions / Quick Reference Guide ...... 11  
Welcome to the Impressa S9 One Touch.................. 11  
9. Coffee Preparation................................................... 16  
9a. Pre-warm Cups.......................................................... 16  
9b. Brewing Coffee and Espresso................................ 16  
9c. Overriding Strength and Cup Size During Brewing ..... 17  
9d. The A La Carte Button............................................... 17  
9e. Using Pre-Ground Coffee .......................................... 17  
10. Auto Cappuccino System........................................ 18  
10a. Preparing the Thermal Milk Container....................... 18  
10b. The Froth XPress System .......................................... 18  
1.  
2.  
3.  
3a. Bean-to-cup, “Crema Coffee” and  
Pressure Brewing....................................................... 12  
3b. Different Coffee Drinks............................................... 12  
3c. Coffee Facts............................................................... 12  
4.  
5.  
6.  
Please Don’t / Please Do ........................................ 12  
Factory Settings / Options......................................... 13  
Preparing the Machine for the First Time............. 14  
10c. Preparing One-Touch Cappuccino,  
Cafe Mocha and Latte............................................. 19  
10d. Preparing One-Touch Latte Machiato.................... 19  
10e. Preparing Hot Milk / Hot Chocolate ...................... 19  
10f. Overriding the Cappuccino Settings ......................... 20  
10g. Cappuccino Rinsing................................................... 20  
10h. Using Hot Water......................................................... 20  
11. Visual Programming of Beverage Portions......... 21  
12. Water Care ................................................................. 21  
6a. Filling the Water Tank................................................. 14  
6b. Filling the Bean Container ......................................... 14  
6c. Turning the Machine On for the First Time ............... 15  
6d. Cup Illumination ......................................................... 15  
7.  
8.  
Adjusting the Grinder................................................. 15  
Daily Preparation........................................................ 15  
9.  
TABLE OF CONTENTS  
Continued  
PAGE  
PAGE  
Care and Maintenance Messages ....................... 29  
12a. Water Hardness Monitor......................................... 21  
15.  
12b. Changing the Water Hardness Monitor .................. 22  
15.1 Manual Maintenance Cycles ................................... 30  
15.2 Removing Stones etc. from the Burr Grinder ......... 31  
15.3 General Cleaning Instructions ................................. 31  
15.4 Emptying the System before Transport................... 31  
15.5 Cleaning the frothXpress ......................................... 31  
13.  
Clearyl Water Filter Cartridge.................................. 22  
13a. Installing and Activating the Clearyl  
Water Cartridge ..................................................... 23  
13b. Automatic Clearyl Replacement.............................. 23  
13c. Manual Clearyl Replacement .................................. 24  
13d. Do Not Let the Clearyl Filter Dry Out!..................... 24  
16.  
Automatic Cleaning Cycles ..................................... 32  
16.1 Cleaning with Special Tablet ................................ 32  
14.  
Programming ......................................................... 24  
16.2 Manual Tablet Cleaning ........................................... 33  
14.1 Re-Programming Beverage Buttons ................... 24  
14.2 Restoring Factory Settings for Beverage Buttons .... 26  
14.3 Economy Modes ..................................................... 26  
14.4 Actual Time and Weekday ...................................... 27  
14.5 Auto-On and Auto-Off Times................................... 27  
14.6 Auto-Off.................................................................... 28  
14.7 Rinse Settings.......................................................... 28  
14.8 Information............................................................... 29  
14.9 Display Settings....................................................... 29  
14.10 Languages................................................................ 29  
17.  
Decalcifying.............................................................. 33  
17.1 Decalcifying Procedure............................................ 34  
17.2 Manual Decalcifying................................................. 34  
18.  
19.  
20.  
21.  
22.  
Tips For Better Coffee ............................................. 35  
Error Messages / Troubleshooting........................... 35  
Supplies................................................................... 36  
Limited Two-Year Warranty...................................... 37  
Free Repair Service / Extra Repair Coverage......... 38  
10.  
IMPORTANT / BATTERY BACK-UP  
The Impressa S9 One Touch has an internal battery back-up for  
without moving your cup, brews one or two cups of crema  
coffee or espressos at a time, produces unlimited amounts of  
the clock functions. After plugging the S9 OT in for the first time, hot frothed and hot steamed milk and delivers up to 15 oz. hot  
turn the Main Power Switch in the back of the machine on (Fig. 1b;  
the red indicator light in the ON/OFF button (Fig. 2,B) will illumi-  
nate). Leave the main power switch on for the first 24 hours to  
insure that the internal battery back-up is fully charged.  
water – all with a push of a button.  
With its two independent stainless steel Thermoblock heating  
systems it switches from brewing coffee to frothing milk without  
any up- or down-time. The two-step pressure brewing system -  
well known in commercial applications - was adapted and  
refined by Jura coffee specialists and is the trademark of each  
Jura-Capresso coffee center. This two step brewing system  
ensures optimal coffee extraction and will finish every cup with a  
rich layer of "crema" - proof for perfectly pressure brewed cof-  
fee. The adjustable, commercial conical burr grinder grinds  
beans to the desired fineness (6 settings). Use pre-ground coffee  
with the separate filler funnel. The second Thermoblock gener-  
ates unlimited steam instantly. Program a specific amount of  
frothed/steamed milk and the S9 OT will always deliver your pre-  
ferred cup size. A separate hot water spout prepares a cup of tea  
or any other hot beverage in seconds. With four pre-set coffee  
buttons, four pre-set milk beverage buttons, a special A La Carte  
button and the easy-to-use Rotary Dial you can prepare thousands  
of different coffee beverages with the push of a button. Override  
or re-program your favorite coffee drinks. Select from different  
maintenance set-ups. The S9 OT automatically reminds you  
when to refill water, clean, change filter or decalcify. The  
"Information" section lets you know how many coffees you pre-  
pared with the different coffee buttons. The beautiful housing,  
cup illumination and informative LED display make the S9 OT  
the most versatile Super Automatic Coffee Center available today.  
Enjoy your Impressa S9 One Touch!  
1. PRODUCT WARRANTY REGISTRATION  
Remove the Product Registration from the Welcome Pack, fill it  
out and mail or fax it to us within two weeks or register your  
Important: This registration is part of your warranty (chapter 21).  
If your retailer sent the product registration to Jura-Capresso when  
you purchased the machine, it is not necessary to register again.  
2. OPERATING INSTRUCTIONS  
QUICK REFERENCE GUIDE / DVD  
Thank you for choosing this Jura-Capresso product.  
Important: Do not try to set-up the Impressa S9 One Touch  
without following the set-up steps in chapter 6 - 8. Or use the  
Quick Reference Guide.  
Take time to study this instruction manual. It covers many  
features of the S9 OT and provides helpful hints and  
will enhance your enjoyment with coffee beverages.  
• We highly recommend viewing the enclosed DVD.  
3. WELCOME TO THE IMPRESSA S9 One Touch  
This fully automatic coffee/espresso/cappuccino center is  
completely programmable and extremely user friendly. The S9  
OT prepares a cup of cappuccino or latte at a push of a button  
11.  
3a. BEAN-TO-CUP / “CREMA COFFEE" /  
Experiment with the size of your milk based drinks. For stronger  
coffee taste add more coffee, for more milk taste add more  
frothed/steamed milk.  
HIGH PRESSURE BREWING  
According to the majority of coffee experts, grinding the beans  
just before brewing, tamping and brewing under high pressure is  
the ideal extracting process for maximum flavor and aroma. Your  
S9 OT automatic coffee center will always produce espresso and  
coffee with a thick, foamy layer called "crema." The crema traps  
the fine aromatics and the light gaseous flavors that register on  
the palate. The high pressure and the short brewing time  
prevent the extraction of bitter oils and release less caffeine than  
any other brewing method.You will always make the absolute  
freshest and most aromatic cup of coffee. This is the reason why  
many European restaurants and hotels serve only fresh pres-  
sured brewed coffee. Experiment with your S9 OT and prepare  
the best and most enjoyable cup of coffee!  
3c. COFFEE FACTS  
Caffeine is tasteless. A "strong" coffee or espresso is mostly  
the result of the amount of coffee in relation to the amount of  
water. The longer a bean is roasted, the less caffeine it has.  
The shorter the brewing time the less caffeine in your cup.  
Arabica and Robusta are two genetically different kinds of  
beans. "Arabica" beans have more flavor and a little less caffeine  
than "Robusta" beans which are mostly used in lower priced  
coffees and instant coffees.  
Espresso is not a bean! It's the way the coffee is roasted and  
prepared. Typical US espresso roasts result in darker beans with  
an oily surface. European espresso roasts are medium brown  
with no or very little oils on the surface.  
3b. DIFFERENT COFFEE DRINKS  
Here are some guidelines for the most popular coffee drinks:  
• Ristretto: 1/2 to 1 oz. of coffee. Sweeten to taste.  
• Espresso: 1 to 2 oz. coffee. Sweeten to taste.  
• Double Shot: 3 to 4 oz. of coffee. Sweeten to taste.  
• Crema Coffee: 5 to 8 oz. of coffee.  
• Cappuccino: 3 to 4 oz. of hot frothed milk plus espresso.  
• Latte: 3 to 5 oz. steamed milk with little or no froth plus espresso.  
• Latte Macchiato: 5 to 6 oz. of frothed/steamed milk produced  
with pause*, plus one or two shots of espresso. *The pause  
separates the milk froth and the milk and allows the espresso  
to settle “in between” (chapter 10d).  
All Display Messages Are Shown in RED  
4. PLEASE, DON’T... (or you void your warranty protection):  
• Never pull out the drawer during the brewing process. Only  
pull the drawer when the display instructs you or when the  
display shows COFFEE READY.  
• Never fill instant coffee into the bean container or ground coffee  
funnel; it will damage the brewing chamber.  
• Never fill sugar coated coffee beans into the bean container.  
• Never fill frozen beans into the bean container. Do not keep  
beans in the freezer. Store them in a dark, airtight container.  
• Never fill anything other than coffee beans into the bean  
container (no chocolate, rice, nuts, spices, etc.).  
• Café Mocha: Use chocolate milk then proceed as in making  
cappuccino or latte.  
12.  
• Never fill anything but fresh, cold clean water into the water  
container, except when decalcifying (chapter 17.1).  
• Never use mineral or carbonated water. You can use tap  
water, bottled water, spring water, distilled water and reverse  
osmosis water.  
Coffee volume:  
• All 1-cup buttons can be programmed to brew between  
0.5 and 8 oz. of coffee.  
• The Hot Water Portion can be programmed to dispense up to  
15 oz. of hot water.  
• Never repair or open the machine yourself. All repairs should  
be performed only by an authorized service center.  
• Do not place the machine on a surface which is sensitive to  
hot or cold water and steam. Never place the machine on an  
uneven surface.  
• All 2-cup buttons can be programmed to brew between  
0.5 and 8 oz. per cup, total of 16 oz. max.  
Tip: if you use a 12 oz. mug and program one of the 2-cup  
buttons to 5 oz. the S9 OT will brew a total of 10 oz. of coffee  
into your mug.  
Coffee strength (AROMA):  
PLEASE, DO...  
• All 1-cup buttons can be set to five different coffee strengths:  
XMILD, MILD, NORMAL, STRONG, XSTRONG.  
In XMILD the conical burrs grind for approx. 5 seconds, in  
XSTRONG, the grinding takes about 9 seconds.  
• When using the 2-cup buttons, the S9 OT will always grind in  
XSTRONG.  
• Fill water tank daily with fresh, cold water.  
• Before filling the bean container, remove any foreign particles  
(small stones) from coffee beans.  
• Let frozen beans thaw for 3 to 4 hours before pouring them  
into the bean container.  
Important: If you pull out the drawer at any time you must empty Please note: The display indicates the five strength settings with  
the used coffee container and the drawer. If you do not empty the  
container, used coffee will overflow inside the machine and can  
cause serious damage to the internal mechanism.  
graphics showing from one to five coffee beans.  
Temperature:  
• All coffee buttons can be set to NORMAL or HIGH.  
• The Hot Water function can be set to LOW, NORMAL, XHIGH  
(XHIGH is used for pre-warming cups and for specialty teas).  
Steaming for milk frothing:  
• The cappuccino and latte macchiato buttons and the milk  
portion can be set to produce steam from 3 to 120 seconds.  
Latte Macchiato Pause:  
5. FACTORY SETTINGS / OPTIONS  
The IMPRESSA S9 One Touch can be set up in many different  
ways. Beverages, on/off settings, temperature, rinse cycles,  
water treatment, energy savings modes and display information  
can be programmed to your personal preferences.  
Beverage buttons can be customized with regards to volume  
(cup size), coffee strength (AROMA), temperature, duration of  
milk steaming/frothing.  
• The pause between milk frothing and coffee brewing can be  
set from 0 to 60 seconds.  
13.  
Factory Settings for Beverage Buttons:  
• All coffee buttons are set to temperature HIGH.  
• The hot water function is set to XHIGH.  
• 1-CUP Espresso button (Fig. 2,C) 2 oz./ STRONG.  
• 2-CUP Espresso button (Fig. 2,F) 2 oz. per cup / XSTRONG.  
• 1-CUP Coffee button (Fig. 2,D) 5 oz./ STRONG.  
• 2-CUP Coffee button (Fig. 2,G) 5 oz. per cup / XSTRONG.  
• A La Carte button (Fig. 3A,N) 7 oz.  
• DO NOT install the Clearyl water filter now (chapter 13a).  
• Make sure the machine sits on an even, flat surface and the  
drawer and used coffee container are inserted (Fig. 1).  
• Plug-in machine.  
6a. FILLING THE WATER TANK  
Please note: Only use fresh, cold water. Never fill water tank  
with carbonated water, milk or any other liquid.  
• Remove the water tank, rinse and fill with fresh, cold water.  
• Replace water tank and make sure that it engages securely.  
• Cappuccino; one-touch button (Fig. 3.6) 14 seconds milk, 0  
seconds pause, 2 oz. coffee / NORMAL.  
• Latte Macchiato; one-touch button (Fig. 3.7) 14 seconds milk,  
15 seconds pause, 2 oz. coffee / STRONG.  
• Milk portion; Selector Dial (Fig. 3.5) 14 seconds milk,  
6b. FILLING THE BEAN CONTAINER  
Please note: To insure that the conical burr grinder will work for  
a long time, do not use it with any kind of coated or flavored  
beans (all coating and flavors contain sugar or sugar substances).  
Such coating can damage the burrs. Using such beans voids the  
warranty. Have your coffee store grind the sugar coated beans  
and use as described in chapter 9e.  
Flavored Coffee: If you like flavored coffees we recommend  
adding flavors to your coffee after brewing. This way you can  
use your regular coffee beans in the bean container. Adding the  
flavors after brewing lets you control the flavor intensity much  
better than with pre-flavored coffee. Your local coffee store  
typically carries a variety of liquid flavors.  
• Water Portion; Selector Dial, 5 oz.; XHIGH.  
Other Factory Settings:  
• 5-hour auto shut-off.  
• Water hardness setting: 10ºdH.  
• Filter: FILTER NO (Clearyl Water Care Cartridge: not installed)  
• Language: English.  
• Display: AM/PM and OZ.  
• Economy Mode (energy saving): Off  
• Time / Weekday: --.-- (not set)  
• Automatic On and Off times: not set  
• Cappuccino Rinsing: set to NOW; display shows  
CAPPUCCINO RINSING immediately after frothing milk.  
• Open the Cover Lid (Fig. 5).  
• Remove the Aroma Protection Lid (Fig. 6).  
• Make sure the bean container is empty and clean. Fill beans  
into the bean container (Fig. 7).  
6. PREPARING THE MACHINE FOR THE FIRST TIME  
• Make sure all accessories, literature and any other items are  
removed from the bean container and the water tank.  
Frozen Beans: Thaw 3 to 4 hours before adding to bean  
container. This prevents moisture from seeping into the grinder.  
14.  
Oily Beans: Beans with an oily surface tend to stick together.  
This may prevent a continuous flow of beans from the bean  
container into the burrs. As a result the grinder does not grind  
enough coffee and you might get weak or no coffee at all.  
Stir the beans in the bean container just before grinding.  
6d. CUP ILLUMINATION  
The cup illumination adds a dramatic touch to brewing coffee.  
Providing the machine is plugged in, you can activate the cup  
illumination for 3 minutes by pressing any button.  
Alternatively, you can also pour the beans into an open bowl and 7. ADJUSTING THE GRINDER  
let them sit for about 5 hours. The oils will evaporate (this will  
not change the taste of your coffee). Then fill the beans into the  
bean grinder. Now beans will feed into the burrs more easily.  
IMPORTANT: The grinding grade can only be adjusted while  
the grinder is actually grinding.  
Adjust the grinder to the roast of your coffee.  
• Light roast: use a finer adjustment (smaller dots).  
• Dark roast: use a coarser adjustment (larger dots).  
• Open the cover of the bean container (Fig. 5).  
6c. TURNING THE MACHINE ON FOR THE FIRST TIME  
• Make sure bean container and water tank are filled.  
• Press the Main Power Switch in the back of the machine (Fig. 1b) • To adjust fineness, turn the grinding wheel during grinding to  
The On/Off button illuminates (Fig. 2.B).  
the desired position (Fig. 9).  
• Push the On/Off button. The display shows FILL SYSTEM /  
PRESS RINSE and the Rinse button (Fig. 2.E) illuminates.  
• Place containers underneath the Auto Cappuccino System  
and the Hot Water Spout (Fig. 4) and push the Rinse button  
(Fig. 2.E). SYSTEM FILLING. The machine will dispense a  
small amount of water. HEATING UP / PRESS RINSE.  
• Place cup underneath the dual coffee spout (Fig. 4) and press  
the Rinse button (Fig. 2.E). MACHINE RINSING. The machine  
will dispense a small amount of water. COFFEE READY.  
Please note: You can only make coffee when the display reads  
COFFEE READY.  
ATTENTION: Oily beans tend to stick together. Stir beans just  
before grinding to ensure a proper flow of beans into the burrs.  
Please note: If coffee does not flow through the Dual Coffee  
Spouts in a constant stream, turn the wheel to a coarser setting.  
8. DAILY PREPARATION  
Fill the water container every morning with fresh, cold water. This  
will enhance the taste of your coffee.  
• Make sure the Main Power Switch is on (Fig. 1b). In this case  
the On/Off button is illuminated.  
• Push the On/Off button. The display shows WELCOME TO  
JURA and then HEATING UP. After approx. 2 minutes the  
display shows PRESS RINSE.  
• Push the Rinse Button* (Fig. 2,E). Hot water will warm up all  
internal parts and pump through the coffee spouts MACHINE  
• Place a cup under the coffee spout and push one of the coffee  
buttons. The machine will grind and brew coffee. If the display  
shows FILL BEANS push one of the coffee buttons again.  
• Discard the first two cups of coffee.  
You are now ready to brew coffee.  
15.  
RINSING. The water will be caught in the drawer underneath.  
The rinse cycle stops by itself and the display reads: COFFEE  
READY. You are now ready to make coffee.  
*Note: S9 OT can be programmed to automatically start the  
rinsing cycle after HEATING UP is displayed (chapter 14.7).  
9. COFFEE PREPARATION  
9a. PRE-WARM CUPS  
In the morning pre-warm your cups with hot water through the  
Hot Water Spout. Cold cups reduce the coffee temperature by  
5ºF to 10ºF.  
Place a cup under the Hot Water Spout, turn the Selector Dial  
(Fig. 3.3) until the display shows HOT WATER and push the  
Selector Dial. The display shows TEMP. XHIGH and water will  
flow into your cup. Push the Selector Dial again to stop and  
discard the water. COFFEE READY.  
8a. TURNING THE MACHINE OFF / RINSING  
Before turning off the S9 OT, place containers under the Dual  
Coffee Spouts and Auto Cappuccino System (Fig. 4).  
When the S9 OT is turned off or turns itself off it will prompt for  
short cleaning cycles as follows:  
9b. BREWING COFFEE AND ESPRESSO  
Only the Dual Coffee spouts were used: The S9 OT displays  
MACHINE RINSING. For a few seconds hot water will be  
dispensed through the Dual Coffee Spouts and through the  
coffee spout of the Cappuccino section. The machine and the  
display turn off.  
The Auto Cappuccino Spouts and the Dual Coffee Spouts  
were used: The S9 OT first displays CLEAN CAPPUCCINO  
and the Rinse button illuminates. If the Rinse button is not  
pushed within the next ten seconds, the display shows SPOUT  
RIGHT / PRESS RINSE. Press the Rinse button. The S9 OT will  
dispense some hot water through the coffee spout of the  
Cappuccino section. It will then push some hot water through  
the Dual Coffee Spouts and turn off.  
The machine has four pre-set coffee buttons, 1 ESPRESSO,  
2 ESPRESSI, 1 COFFEE, 2 COFFEES (Fig. 2).  
All buttons are pre-set for coffee strength, coffee volume and  
temperature (chapter 5).  
• Place one or two cups underneath the Dual Coffee Spouts  
and push the desired button. The machine will grind, tamp  
and then brew the coffee. It uses a 2-step brewing process  
(pre-brew phase), pauses for a few seconds, and then starts  
the brewing process. The display will show the name of the  
button you pushed, e.g. 1 ESPRESSO and the selected coffee  
strength indicated by a bean graphic, e.g. 4 beans = strong.  
Please note: when pushing any of the two-cup buttons, the  
coffee strength is not displayed.  
Please note: When the S9 OT turns off you may hear a slight  
hissing noise.  
Important: After the brewing stops the machine will discard the  
used coffee grounds. Please do not try to pull out the drawer  
(Fig.1,18) during this operation. It can seriously damage the  
machine.There is no need to pull out the drawer until the display  
shows the message EMPTY TRAY or EMPTY GROUNDS.  
16.  
Please note: You can always stop the brewing process by  
before brewing. COFFEE READY.  
pressing any of the coffee buttons.  
• Push the A LA CARTE button (Fig. 3A.N). The display shows  
A LA CARTE and the strengths indicated by the bean graphic  
e.g. 2 beans (mild).  
• Turn the Rotary Dial to choose any of five strength settings:  
XMILD, MILD, NORMAL, STRONG, XSTRONG, indicated by  
1 to 5 beans in the bean graphic.  
• Then push the Rotary Dial. The machine starts grinding. Now  
dial the coffee volume.  
Please note: If you push the A LA CARTE button and do not  
push the Rotary Dial within a few seconds, the display will  
revert to COFFEE READY.  
9c. OVERRIDING STRENGTH AND CUP SIZE DURING  
BREWING  
During brewing you can override the strength of the two one-  
cup buttons (Fig. 2, C, D) and the cup size of all four coffee  
buttons. When using the two-cup buttons the S9 OT automati-  
cally selects the maximum strength. Overriding will not change  
the factory setting (chapter 5).  
Example:  
• Open the cover for the Rotary Dial (Fig. 1.19).  
• Push the 1-Cup Coffee Button (Fig. 2D).  
• During grinding turn the Rotary Dial to change the strength to  
e.g. XSTRONG (5 bean graphic). The display shows the  
selected strength.  
• When the coffee starts brewing, turn Rotary Dial until the display  
shows, e.g. 7.0 OZ. The S9 OT will brew 7.0 oz of coffee.  
If you use the same coffee button again and do not use the  
Rotary Dial, the S9 OT will brew a cup according to the  
programmed settings for this button.  
Please note: When using one of the 2-Cup buttons you can  
only change the cup size. The display shows the amount per  
cup, e.g. 6.0 OZ; the S9 OT will brew a total of 12 ounces.  
For re-programming see chapter 11 (cup sizes) and chapter 14.1  
for cup sizes, temperature and strength.  
9e. USING PRE-GROUND COFFEE  
You can also use pre-ground coffee, bypassing the grinder. This  
is convenient if someone requests decaf coffee or a decaf  
cappuccino or flavored coffee.  
Please note: Never fill the funnel with instant coffee. Do not fill  
the funnel with more than two scoops. The funnel is not a  
storage container. If coffee is ground too fine the brewing  
process may be stopped.  
COFFEE READY  
• Open cover (Fig. 1,19) and push the Ground Coffee button  
(Fig. 3A,O). FILL PRE-GROUND / COFFEE READY.  
• Fill 1 or 2 level measuring scoops of ground coffee into the  
opening for ground coffee (Fig. 1,11) and close the lid.  
• Now push one of the four coffee buttons to brew your coffee  
e.g. 1 COFFEE. The pre-ground coffee is tamped and brewed.  
ENJOY, then COFFEE READY.  
9d. THE A LA CARTE BUTTON  
The S9OT has a fifth coffee button (Fig. 3A,N). With this button  
you can change the coffee volume and the coffee strength just  
17.  
Please note: If the Ground Coffee button (Fig. 3A,O) is  
pressed by mistake just press one of the coffee buttons, NOT  
ENOUGH PRE-GROUND. The machine will automatically stop  
and return to COFFEE READY.  
Please note: After use of sugar coated or flavored coffee  
through the pre-ground coffee funnel you may experience some  
flavor transfer when switching back to your regular coffee.  
• Rinse the milk container with fresh water before first use and  
fill with fresh cold milk. Close the lid.  
• Insert one end of the short flexible hose into the lid opening.  
• Remove the red cap from the side of the frothXpress and  
insert the other end of the short flexible hose (Fig. 15).  
You are ready to steam/froth milk.  
Storing the milk container: always remove the outside flexible  
hose and open the lid before storing the milk container in the  
refrigerator.  
10. AUTO CAPPUCCINO SYSTEM  
The S9 OT features the Auto Cappuccino System with two spouts  
located behind each other (Fig. 15) The front spout produces  
steam (steam nozzle). The rear spout produces high pressure  
brewed coffee. Attached to the steam nozzle is the removable  
frothXpress system. It siphons, steams and froths milk.  
The S9 OT Cappuccino System prepares a variety of milk based  
drinks without ever moving the cup: Cappuccino, Latte, Latte  
Macchiato, Café Mocha, Hot Milk, Hot Chocolate.  
Important: The milk container is not dish washer safe. Do not  
immerse the milk container in any liquid.  
Using the long flexible hose: To siphon milk directly from a milk  
carton use the long flexible hose. Insert one of the black con-  
necting pieces in the straight-cut end of the hose and insert into  
the frothXpress. Insert the other end with the V-cut into the milk  
container (Fig. 17).  
10b. THE FROTHXPRESS SYSTEM  
This system produces unlimited amounts of hot steamed or  
frothed milk right into your cup.  
10a. PREPARING THE THERMAL MILK CONTAINER  
The S9 OT comes with a 20 oz. double walled vacuum stainless  
steel container. This custom-made milk container can keep cold  
milk cold for up to eight hours. There is no need to worry about  
the milk getting warm during the day.  
The milk container comes complete with: • lid and attached  
stainless steel hose • two short flexible hoses • one long flexible  
hose • spare black and transparent fittings (Fig. 14a, 14b).  
The two short hoses have a connecting piece on each end.  
• Unscrew the milk container lid. A stainless steel hose is  
attached to the inside of the container. A small transparent  
fitting holds the hose in place (a spare fitting is included).  
Important: This system siphons milk and mixes it inside the  
frothXpress with hot steam. It is necessary that all parts are  
connected tightly, otherwise the siphoning process will not work.  
Frothing Position: The dial points to the upper part of the face  
(12 to 2 o’clock). This section is used for Cappuccino and Latte  
Macchiato. In the 12 o’clock position the frothXpress creates the  
most milk froth. Turning the dial towards the 2 o’clock position  
increases the milk temperature (Fig. 16).  
Steaming Position: The dial points to the lower part of the face  
18.  
(6 to 4 o’clock). Milk will be steamed, not frothed. Turning the  
dial towards the 4 o’clock position increases milk temperature.  
Steam Only Position: When the dial points to the steam symbol  
(3 o'clock), the siphoning is blocked. Only steam will pass  
through the frotherXpress.  
Please note: You can always stop the beverage preparation by  
pushing any of the beverage buttons.  
10d. PREPARING ONE-TOUCH LATTE MACCHIATO  
This beverage is very popular in Europe. It is normally served in  
glasses, approx. 4 to 5 inches tall and 2 inches in diameter.  
10c. PREPARING ONE-TOUCH CAPPUCCINO, CAFÉ MOCHA COFFEE READY.  
AND LATTE  
The frothXpress dial points to the 12 to 2 o’clock position.  
COFFEE READY.  
The frothXpress dial points to area between 12 and 2 o’clock  
The milk container is connected.  
• Place your latte macchiato glass underneath the Cappuccino  
system and push the Latte Macchiato button (Fig. 3.7). The S9  
OT starts grinding, the display shows LATTE MAC. and the  
coffee strength. It then siphons, heats and froths milk for 14  
seconds and pauses. The display shows PAUSE (factory  
setting is 15 seconds). During this time the milk separates  
from the milk froth. After the pause 2 oz. of high-pressure  
brewed coffee are automatically added. LATTE MAC. Then  
ENJOY. The coffee settles between the froth and the milk  
giving the beverage the typical multi-layered, Latte Macchiato  
look. COFFEE READY.  
• Place your cappuccino cup underneath the Cappuccino  
system and push the cappuccino button (Fig. 3.6). The S9 OT  
starts grinding, the display shows CAPPUCCINO and the  
coffee strength (bean graphic). It then siphons, heats and  
froths milk for 14 seconds and adds 2 oz. of high-pressure  
brewed coffee (Factory Settings, chapter 5). The display  
shows ENJOY then COFFEE READY.  
Tip: If you use a glass cup you can see how much froth is  
created and how the coffee sits beneath the layer of milk froth.  
Slightly stir to distribute the coffee evenly into the hot milk.  
10e. PREPARING HOT MILK / HOT CHOCOLATE  
The Cappuccino System can produce hot milk or hot chocolate  
without brewing coffee.  
CAFÉ MOCHA: use chocolate milk or add chocolate syrup to  
your cold milk and stir then proceed as explained before.  
COFFEE READY.  
LATTE: turn the frothXpress dial between the 4 and 6 o’clock  
position and repeat above steps. Milk is steamed without froth.  
Please note: You can always add an additional shot of espresso  
by placing your cup under the Dual Coffee Spouts (Fig. 4) and  
pushing the 1-Cup Espresso button. You can also add additional  
hot milk (chapter 10e).  
• Connect the milk container to the frothXpress system or use  
the long flexible hose inserted into any milk carton.  
• Place your cup underneath the Cappuccino system.  
Turn the Selector Dial (Fig. 3.3) until the display shows MILK  
or MILK PORTION ("MILK" siphons milk until you stop the  
action by pushing the Selector Dial button again.  
19.  
"MILK PORTION" siphons milk for a programmed time and  
stops automatically).  
• Push the button inside the Selector Dial. The display shows  
MILK or MILK PORTION. During this time hot steamed /  
frothed milk is created and delivered into your cup.  
COFFEE READY.  
COFFEE READY / RINSE CAPPUCCINO and the Rinse button  
illuminates. You can still continue making any beverages. We  
recommend to perform the cappuccino rinsing since it takes  
only a few seconds and makes sure that your frothXpress is free  
of any milk.  
Turn the frothXpress dial to the 3 o’clock position (Fig. 16) and  
place a cup underneath the cappuccino system.  
• Push the Rinse button. The display shows CAPPU. RINSING.  
Hot water is pushed through the frothXpress for a few seconds.  
COFFEE READY.  
10f. OVERRIDING THE CAPPUCCINO SETTINGS  
As with the coffee buttons you can override the pre-programmed  
volumes of the milk beverage buttons.  
Example: The factory setting for the Cappuccino button is normal  
strength (3 beans graphic), 14 seconds of milk frothing and 2 oz.  
of coffee. Prepare a one-time special cappuccino, extra strong  
(5 beans graphic), more milk froth (20 seconds) and 3 oz. of coffee.  
COFFEE READY  
Turn the frothXpress dial back to your preferred position.  
IMPORTANT: If you do not use the Cappuccino Rinsing cycle,  
milk droplets might harden inside the frothXpress, resulting in  
insufficient frothing performance.  
• Place your cappuccino cup under the Cappuccino system  
and open the cover for the Rotary Dial (Fig. 1.19).  
• Push the Cappuccino Button (Fig. 3.6). During grinding turn  
the Rotary Dial to change the strength until the display shows  
the 5 bean-graphic.  
10h. USING HOT WATER  
The hot water function lets you pre-warm cups, brew tea, make  
a quick cup of soup, or add hot water to your coffee or espresso  
to create a milder flavor.  
• When the frothing starts turn the rotary dial until the display  
shows 20 SEC.  
• When the coffee brewing starts turn the Rotary Dial until the  
• Place a cup under the hot water spout (Fig. 4).  
Turn the Selector Dial (Fig. 3.3) until the display shows HOT  
WATER or HOT WATER PORTION (HOT WATER PORTION  
delivers a pre-programmed amount of hot water and then  
stops automatically. HOT WATER delivers hot water until you  
stop the action by pushing the Selector Dial button again).  
• Push the button inside the Selector Dial. The display shows  
the pre-set temperature e.g. TEMPERAT. X HIGH and then  
HOT WATER or HOT WATER PORTION.  
display shows 3.0 OZ.  
10g. CAPPUCCINO RINSING  
In only a few seconds this rinsing program removes milk droplets  
inside the frothXpress.  
After preparing a beverage with milk (Cappuccino Button, Latte  
Macchiato Button, Milk, Milk Portion) the S9 OT display shows  
COFFEE READY.  
20.  
The temperature for this function can be set to LOW, NORMAL  
and XHIGH (chapter 14.1; example 3)  
The next time you push the Cappuccino button, the S9 OT will  
produce that amount of milk and coffee.  
You can override the WATER PORTION during the hot water  
release with the Rotary Dial.  
12. WATER CARE  
You can re-program the hot water portion (chapter 14.1).  
The S9 OT works with: • tap water • bottled water • distilled  
water. We recommend using tap water or bottled water. Distilled  
water has no minerals and does not improve the taste of coffee.  
Water that is heated inside the machine leads to calcium deposits.  
Tap water has a varying degree of water hardness (chapter 12a).  
Most bottled water has a low level of water hardness.  
IMPORTANT: do not use carbonated water or any other liquid in  
the water tank.  
You have the following options to take care of the water.  
• Decalcifying System (chapter 17.1).  
• Clearyl Water Filter Cartridge (chapter 13a).  
The machine is factory pre-set to automatically remind  
you to decalcify.  
11. VISUAL PROGRAMMING OF BEVERAGE PORTIONS  
Chapters 14 and 14.1 explain how to re-program all parameters  
(volume, strength, temperature) for the beverage buttons.  
Re-programming the cup size for coffee and milk can also be  
done during beverage preparation as follows:  
• Push and hold the beverage button you want to re-program  
until display shows ENOUGH COFFEE? or ENOUGH MILK?  
This way you can make sure your (cappuccino) cup is  
completely filled with milk and coffee.  
Example:  
Visually re-programming the Cappuccino button (Fig 3.6).  
COFFEE READY.  
• Prepare the Cappuccino Systems (milk container etc) to make  
a cappuccino and place your cappuccino cup under the  
frothXpress.  
• Push and hold the Cappuccino button until display shows  
ENOUGH MILK?  
12a. WATER HARDNESS MONITOR  
Your S9 OT is set to a water hardness of 10ºdH and will auto-  
matically indicate when it is time to perform a decalcifying cycle.  
You can change the water hardness setting from 1º to 30ºdH. If  
you are not sure about the hardness of your water, ask your local  
• When the desired amount of milk and milk froth is in your cup, water company for the "Water Hardness in Grains." The machine  
push the Cappuccino button again. The display now shows  
ENOUGH COFFEE?  
• When enough coffee has been added to your frothed milk  
push the Cappuccino button again. CONFIRMED , then  
ENJOY, then COFFEE READY.  
displays the water hardness in the German hardness scale which  
is a bit different from the American "Grain" scale (see chart  
below). You can also use the water hardness indicator strip  
("Aquadur" in Welcome Pack) to determine the water hardness:  
• Insert the strip for one second into the water you want to  
use. Shake off any access water and wait for one minute.  
21.  
One or more sections of the indicator strip will turn reddish.  
• Change the water hardness setting according to the table  
below.  
• Push the Rotary Dial to enter the program.  
Turn the Rotary Dial until the display shows 20ºdH.  
• Push the Rotary Dial to confirm the setting. CONFIRMED ꢀ  
and then HARDNESS 20ºdH.  
Turn the Rotary Dial until the display shows EXIT.  
• Push the Rotary Dial COFFEE READY.  
Display Equivalent Indicator Strip  
German American number of  
Level  
Display  
Degree Grains  
"reddish" fields  
The machine will automatically remind you when it is time to  
decalcify (chapter 17.1).  
Please note: You can set the hardness monitor to INACTIVE.  
In this case you must use distilled water. In this setting the  
S9 OT will not remind you to decalcify the machine.  
Not Active*  
1. extremely soft water  
2. soft water  
3. medium water  
4. hard water  
5. very hard water  
6. extremely hard water  
INACTIVE  
1-4  
5-9  
1-5  
6-11  
None  
1 to 2  
10-14 13-18 2 to 3  
15-19 19-24 3 to 4  
20-24 25-30 4 to 5  
25-30 32-38 All 5  
13. CLEARYL WATER FILTER CARTRIDGE  
The machine comes with one Clearyl Water Filter Cartridge. The  
Clearyl cartridge  
• Reduces the water hardness up to 75%.  
*Not Active: You can only use this setting for distilled water.  
Level 5 and Level 6: If the tap water falls into these two cate-  
gories, decalcifying will be frequent. In this case bottled water is  
recommended. Most bottled water has a low calcium level.  
Please note: If your water has a high calcium content (level 5 or 6)  
and you use the Clearyl Filter Cartridge we recommend to decalcify  
the machine once or twice a year (chapter 17 and 17.1).  
• Removes (if present) up to 85% chlorine, up to 90% lead, up  
to 95% copper and up to 67% aluminum.  
• Cleans the water through an upward current principle (Fig. 10)  
just before the brewing cycle starts, ensuring freshly filtered  
water every time you make coffee.  
• Lasts for 75 liters (~2,500 oz.) of water or up to two months.  
• Eliminates decalcifying except when using very hard water  
(25 grains or higher), see chapter 12. In this case we recom-  
mended to decalcify the machine once or twice a year.  
To reorder cartridges, see chapter 20.  
Please note: If you use Spring or Bottled Water with low calcium  
levels you can set the hardness to 3ºdH, "extremely soft water".  
12b. CHANGING THE WATER HARDNESS MONITOR  
COFFEE READY  
Example: change the hardness setting from 10ºdH to 20ºdH  
• Push the Rotary Dial until display shows MAINTENANCE.  
Turn Rotary Dial until the display shows HARDNESS 10º DH.  
22.  
13a. INSTALLING & ACTIVATING THE CLEARYL WATER  
CARTRIDGE  
Installing:  
and out through the frothXpress system. Initially, the water may  
have a slight discoloration. The program will stop automatically.  
The display shows COFFEE READY.  
Important: Never install the cartridge before or during  
"Preparing Machine For The First Time" (chapter 6).  
6. Turn the frothXpress dial back to your preferred setting.  
Please note: As long as the filter is activated, the water  
• Remove cartridge from its bag and rinse cartridge under water. hardness setting is automatically turned off.  
• Add the extension rod to the cartridge (Fig. 11).  
• Remove the water tank, make sure it is empty.  
• Pull up the cartridge holder and insert the cartridge with its  
tapered end down into the water container (Fig. 12, Fig. 13).  
Make sure it fits securely inside the fins. Push down gently  
(Fig. 13).  
• Close the cartridge holder. Make sure the holder snaps into  
place.  
• Fill the water tank with fresh cold water and replace.  
13b. AUTOMATIC CLEARYL REPLACEMENT  
The filter is monitored automatically. After approx. 75 liters of  
water (~2,500 oz.) the display shows COFFEE READY /  
CHANGE FILTER. The Rinse Button will light up.  
Important: Once the filter has lost its calcium suppressing  
abilities, calcium will build up inside the machine. Since the  
Water Hardness Selector is off, the machine will not remind you  
when to decalcify. If the filter is not replaced, the calcium build-  
up will clog and damage your machine.  
• Push the Rinse Button. DURATION 2 MIN. / START YES.  
Please note: To change and activate the filter at a later time,  
turn the Rotary Dial until the display shows START NO. Push the  
Rotary Dial to exit the program. In this case the S9 OT will still  
remind you with the message CHANGE FILTER.  
1. Push Rinse Button again. CHANGE FILTER /PRESS RINSE.  
2. Remove the water tank and the old filter and set the extension  
rod aside. Important: Keep the extension rod.  
Activating:  
You must activate the cartridge for the machine to monitor it  
properly. Otherwise the S9 OT assumes decalcifying mode.  
COFFEE READY.  
1. Push the Rotary Dial until display shows MAINTENANCE.  
2.Turn the Rotary Dial until the display shows FILTER NO and  
push the Rotary Dial to enter the program.  
3.Turn the Rotary Dial until FILTER YES is displayed and push  
the Rotary Dial. CONFIRMED is displayed briefly and then  
3. Make sure the water tank is empty.  
INSERT FILTER/PRESS STEAM. The Rinse button illuminates.  
4.Place a 20 oz. container under the frothXpress (Fig. 4) and  
turn the frothXpress dial to the 3 o'clock position.  
4. Remove the new cartridge from its bag and rinse under  
running water. Now install as explained in chapter 13a,  
steps 4 through 6.  
5.Push the Rinse Button. FILTER RINSING. For the next 60  
seconds the machine will push water through the cartridge  
23.  
13c. MANUAL CLEARYL REPLACEMENT  
If the filter is more than 2 months old and the display does not  
indicate to replace filter, replace as follows.  
• Push the Rotary Dial until display shows MAINTENANCE.  
Turning the Rotary Dial clockwise the display shows the follow-  
ing functions:  
COFFEE READY.  
• Push the Rotary Dial until the display shows MAINTENANCE.  
• Push Rotary Dial again, display shows CLEAN CAPPUCCINO.  
Chapter  
MAINTENANCE .............. 15.1  
PRODUCTS ..................... 14.1 (beverage buttons)  
Turn the Rotary Dial until the display shows CHANGE FILTER. FILTER NO or YES........... 13a  
• Push the Rotary Dial. The display shows DURATION 2 MIN./  
START YES.  
• Push Rotary Dial again. Display shows INSERT FILTER /  
PRESS STEAM.  
HARDNESS 10ºDh .......... 12b If FILTER YES this function is suppressed.  
ECONOMY MODE – ........ 14.3  
TIME --.-- ......................... 14.4  
UNIT ON/OFF................... 14.5  
OFF AFTER ...................... 14.6  
RINSES............................. 14.7  
INFORMATION................. 14.8  
SETTING AM/PM / OZ .. 14.9  
LANGUAGE ENGLISH..... 14.10  
EXIT  
• Now install as explained in chapter 13a, steps 4 through 6.  
13d. DO NOT LET THE CLEARYL FILTER DRY OUT!  
If the filter is not immersed in water for a few days the granular  
inside will dry out and block any water from passing through.  
• If machine is not used for a few days, leave some water in the  
water tank so the filter will not dry out. Upon using the  
machine again, fill the water tank with fresh water and process  
approx. 2 oz. of water through the hot water spout. You now  
have fresh water for your first cup of coffee.  
• If the machine is not used for a longer period of time, empty  
the water container and remove the CLEARYL filter. Fill a  
glass with at least 2 inches of water and immerse the filter.  
Place the glass in the refrigerator.  
Please note: to get back to COFFEE READY, turn the Rotary  
Dial until the display shows EXIT, then push the Rotary Dial.  
14.1 RE-PROGRAMMING BEVERAGE BUTTONS (PRODUCTS)  
This program allows you to change all parameters for all bever-  
age functions.  
The following parameters can be changed, where applicable:  
Coffee volume (WATER): for all 1-cup buttons from 0.5 to 8 oz.,  
for all 2-cup buttons from 0.5 to 8 oz. per cup (max total 16 oz.)  
Coffee strength (AROMA) for all 1 cup buttons choose from five  
settings: XMILD, MILD, NORMAL, STRONG, XSTRONG. The  
display shows from one to five coffee beans to indicate the  
selected strength during brewing.  
• When you use the machine again, install the filter.  
14. PROGRAMMING  
The S9 OT provides programming, maintenance  
and look-up functions. With the display at COFFEE READY  
you can access the following functions:  
24.  
Temperature: for all coffee drinks the temperature can be set to  
NORMAL or HIGH  
10.Turn the Dial until the display shows TEMPERAT. NORMAL.  
11.Push the Rotary Dial to confirm: CONFIRMED then  
MILK PORTION: steaming can be set from 3 to 120 seconds.  
PAUSE: the pause time between milk production and coffee  
brewing for the one-touch Cappuccino and Latte Macchiato  
buttons can be set from 0 to 60 seconds.  
HOT WATER PORTION: can be set from 0.5 to 15 oz.  
The temperature for the hot water function can be set to LOW,  
NORMAL or XHIGH (for specialty teas and pre-warming cups).  
TEMPERAT. NORMAL.  
12.Turn the Rotary Dial until the display shows EXIT and push the  
Rotary Dial. SELECT PRODUCT.  
13.If you do not want to change another button, turn the dial  
until the display shows EXIT and push the Rotary Dial:  
COFFEE READY.  
Example 1:  
Example 2:  
Re-program the 1-Cup Coffee button to:  
Re-program the Latte Macchiato button to:  
4 ounces of coffee, mild, normal temperature.  
COFFEE READY  
3.5 oz. of coffee, extra strong, milk production for 20 seconds,  
pause to 10 seconds, temperature stays as is (HIGH).  
COFFEE READY  
1. Push the Rotary Dial until the display shows MAINTENANCE.  
2. Turn the Rotary Dial to PRODUCTS and push the Rotary  
Dial. The display shows SELECT PRODUCT.  
3. Push the Latte Macchiato button. The display shows the  
current coffee volume setting, e.g. COFFEE 2.0 OZ.  
4. Push the Rotary Dial, COFFEE 2.0 OZ, and turn the dial until  
the display shows COFFEE 3.5 OZ.  
1. Push the Rotary Dial until the display shows MAINTENANCE.  
2. Turn the Rotary Dial to PRODUCTS and push the Rotary  
Dial. The display shows SELECT PRODUCT.  
3. Push the 1-CUP COFFEE button. The display shows the  
current volume setting, e.g. WATER 5.0 OZ.  
4. Push the Rotary Dial: WATER 5.0 OZ and turn the dial until  
the display shows WATER 4.0 OZ.  
5. Push the Dial to confirm: CONFIRMED then WATER 4.0 OZ.  
5. Push the Rotary Dial to confirm: CONFIRMED then  
6. Turn the Rotary Dial until the display shows AROMA and the  
current strength setting, e.g. three beans graphic.  
COFFEE 3.5 OZ.  
7. Push the Rotary Dial, NORMAL with three beans graphic,  
and turn the Dial until display shows MILD with two beans.  
8. Push the Rotary Dial to confirm: CONFIRMED then  
MILD with two beans.  
9. Turn the Dial until the display shows TEMPERAT. HIGH  
and push the Rotary Dial TEMPERAT. HIGH.  
6. Turn the Rotary Dial until the display shows AROMA and the  
current strength setting, e.g. three beans.  
7. Push the Rotary Dial, STRONG with four beans, and turn  
the Dial until the display shows XSTRONG with five beans.  
8. Push the Rotary Dial to confirm: CONFIRMED then  
XSTRONG with five beans.  
25.  
9. Turn the Rotary Dial until the display shows MILK 14 SEC  
10.Push the dial, MILK 14 SEC, and turn the dial until the  
display shows MILK 20 SEC.  
6. Push the Rotary Dial to confirm: CONFIRMED then  
WATER 7 OZ.  
7. Turn the Rotary Dial until the display shows EXIT and push  
the dial. SELECT PRODUCT.  
11.Push the Rotary Dial to confirm: CONFIRMED then  
MILK 20 SEC.  
8. If you do not want to change another button, turn the dial  
until the display shows EXIT and push the Rotary Dial:  
COFFEE READY.  
12.Push the Rotary Dial until the display shows PAUSE 15 SEC.  
13.Push the Rotary Dial, PAUSE 15 SEC, and turn the Rotary  
Dial until the display shows PAUSE 10 SEC.  
14.2 RESTORING FACTORY SETTINGS FOR BEVERAGE  
BUTTONS  
You can reset the beverage buttons back to the factory setting  
14.Push the Rotary Dial to confirm: CONFIRMED then  
PAUSE 10 SEC.  
15.Turn the Rotary Dial until the display shows EXIT and push  
the dial. SELECT PRODUCT.  
16.If you do not want to change another button, turn the dial  
until the display shows EXIT and push the Rotary Dial:  
COFFEE READY.  
as follows:  
The machine is plugged in. Only the main power switch in the  
back of the machine is on. The display is blank.  
Example: reset the 1-CUP Espresso button.  
• Open the cover of the Rotary Dial.  
• Push and hold the Rotary Dial and push the 1-Cup Espresso  
button for two seconds. The display shows 1 ESPRESSO OK.  
The factory setting has been restored.  
Example 3:  
Change the Hot Water Portion to 7 ounces and and leave the  
temperature at XHIGH.  
COFFEE READY  
14.3 ECONOMY MODES  
You can set the machine to three different modes.  
ECONOMY MODE – (SAVE NO)  
The S9 OT is always ready to brew coffee and produce steam.  
The two white indicator lights in the cappuccino and latte  
macchiato button are always on.  
ECONOMY MODE 1 (SAVE LEVEL 1)  
The machine is always ready to brew coffee and is in the  
1. Push the Rotary Dial until the display shows MAINTENANCE.  
2. Turn the Rotary Dial to PRODUCTS and push the Rotary  
Dial. The display shows SELECT PRODUCT.  
3. Turn the Selector Dial (Fig. 3.3) on the right side until the  
symbol for the Hot Water Portion is illuminated (Fig. 3.1).  
Then push the Selector Dial.  
4. Display shows the current water portion, e.g. WATER 5 OZ.  
5. Push the Rotary Dial, WATER 5 OZ, and turn the dial until  
the display shows WATER 7 OZ.  
energy saving mode for steam.  
26.  
If the machine is primarily used for coffee this setting saves  
energy. The heating element for steam (milk frothing) will shut off  
after approx. 10 minutes after last use. At this time the white  
indicator lights in the cappuccino and latte macchiato buttons  
turn off. To use the steam function, push the cappuccino or latte  
macchiato button. The lights will start blinking, indicating that  
the thermoblock for steam is heating up. This will take between  
5 and 30 seconds depending how much that thermoblock was  
cooled down. Once the white indicator lights in those buttons  
are illuminated, you can push them again to make cappuccino.  
ECONOMY MODE 2 (SAVE LEVEL 2)  
This setting will save more energy than economy mode 1.  
Choose this setting if you prepare only a few coffees or cappuc-  
cinos in large intervals. It is much faster than turning the  
machine on and off every time you want to make coffee.  
Five minutes after last use the S9 OT will lower the temperature  
and enter standby mode. When making coffee at a later time,  
the S9 OT will first heat up for 5 and 30 seconds.  
Example:  
Set the time to 7:15 AM and the weekday to Wednesday.  
COFFEE READY  
• Push the Rotary Dial until the display shows MAINTENANCE.  
Turn the Dial until the display shows TIME -.- / WEEKDAY.  
• Push the Dial and turn to TIME and push the dial again.  
Turn the Dial to select the hours 7:00 AM and push to confirm.  
• Now turn the Dial to set the minutes: 7:15 AM.  
• Push the Dial to confirm. TIME 7:15 AM. CONFIRMED ,  
then TIME 7:15 AM.  
Turn the Dial to WEEKDAY and push the dial.  
Turn the dial until display shows WEDNESDAY and push to  
confirm: CONFIRMED then WEEKDAY WEDNESDAY.  
Turn Dial to EXIT and push to get back to COFFEE READY.  
Please note: For Daylight Saving you have to re-set the time.  
Please note: When fully charged, the built-in back-up battery  
keeps the clock running for up to eight weeks in case the S9 OT  
is unplugged or the main power switch in the back is turned off.  
Example:  
Change from ECONOMY MODE – to ECONOMY MODE 1  
COFFEE READY  
• Push and hold the Rotary Dial. MAINTENANCE  
Turn the Dial until the display shows ECONOMY MODE - .  
• Push the Dial, SAVE NO and turn to SAVE LEVEL 1 and push  
the dial to confirm, CONFIRMED then ECONOMY MODE 1.  
14.5 AUTO-ON and AUTO-OFF TIMES  
You can set a time at which the machine automatically turns on  
and is ready to make coffee.  
Please note: Auto-on/off times will only work if the actual time is  
set and the main power switch is turned on (the small red light in  
the On/Off switch is illuminated)  
Turn the Dial to EXIT and push to return to COFFEE READY.  
Please note: The Auto-on/off time function will apply to all days.  
You can select certain days of the week for the S9 OT not to  
turn on automatically. See the following example.  
14.4 ACTUAL TIME and WEEKDAY  
Setting the time allows you to program auto-on time.  
27.  
Example:  
Example:  
Set the On-time to 6:15 AM and program the S9OT not to turn  
on automatically on Sundays.  
Change the auto-off from 5 hours to 2 hours after last use.  
COFFEE READY.  
COFFEE READY  
• Push the Rotary Dial until the display shows MAINTENANCE.  
Turn the Dial until the display shows OFF AFTER 5 H.  
• Push the Dial OFF AFTER 5 H.  
Turn the dial until display show OFF AFTER 2 H and push to  
confirm. CONFIRMED , OFF AFTER 2 H.  
• Push the Rotary Dial until the display shows MAINTENANCE.  
Turn the Dial until the display shows UNIT ON/OFF.  
• Push the Dial UNIT ON --.--, push again UNIT ON --.--.  
Turn the dial to set the hours UNIT ON 6:00 AM and push the  
Dial to confirm. UNIT ON 6:00 AM.  
Turn the dial to EXIT and push. COFFEE READY.  
Turn the Dial to set the minutes UNIT ON 6:15 AM and push  
to confirm. CONFIRMED , then UNIT ON 6:15 AM.  
14.7 RINSE SETTINGS  
Turn the Rotary Dial until ON/OFF / MON YES is displayed  
and push ON/OFF / MON YES.  
This program allows you to change both the Rinse cycle and the  
Cappuccino Rinse cycle.  
Turn the dial until ON/OFF / SUN YES is displayed and push  
ON/OFF / SUN YES.  
Turn the dial until display shows ON/OFF / SUN NO and push  
to confirm CONFIRMED and then ON/OFF / SUN NO.  
Turn the dial to EXIT and push. The display shows  
ON/OFF / MON YES.  
Rinse cycle (INIT RINSE)  
After turning the machine on with the On/Off button, the S9 OT  
heats up and then prompts you to run a short rinse cycle  
(chapter 8). You can re-program this function so that this rinse  
cycle is done automatically.  
Example:  
Change the initial rinse cycle from manual to automatic:  
COFFEE READY.  
Turn the dial to EXIT and push. COFFEE READY.  
• Push the Rotary Dial until the display shows MAINTENANCE.  
Turn the Dial until the display shows RINSES and push the  
dial. INIT RINSE MANUAL.  
• Push the dial again, INIT RINSE MANUAL and turn to  
INIT RINSE AUTO and push to confirm. CONFIRMED ꢀ  
then INIT RINSE AUTO.  
Turn the dial to EXIT and push the dial RINSES.  
Turn the dial to EXIT and push COFFEE READY.  
14.6 AUTO-OFF  
The S9 OT is pre-set to turn itself off 5 hours after last use.  
You can change the auto-off interval between 0.5 and 15 hours  
or you can set the machine not to turn itself off.  
Recommendations: If you only use the machine in the morning,  
change the auto-off to 2 hours. If you use the machine all day  
long, leave the auto/off as is. This way the machine is always  
ready, and it is not necessary to turn it on and to warm up.  
28.  
CAUTION / WARNING  
14.10 LANGUAGES  
In the setting INIT RINSE AUTO the machine will automatically  
You can change the display from English to French, Portuguese,  
dispense hot water through the Dual Coffee Spouts. Please keep German, Italian, Dutch or Spanish.  
children and pets away!  
COFFEE READY  
• Push the Rotary Dial until the display shows MAINTENANCE.  
Turn the Dial until the display shows LANGUAGE ENGLISH.  
• Push and turn the Dial until the desired language appears and  
push to confirm.  
Turn the Dial to EXIT (in the language you choose).  
• Push the Dial to get back to COFFEE READY (in the  
language you choose).  
Cappuccino rinse cycle (CAPP RINSE)  
The S9 OT is factory-set to immediately remind you to run a  
rinse cycle after milk use (chapter 10g). This function can be  
re-programmed to remind you 10 minutes after last milk use.  
14.8 INFORMATION  
In this program you can look up  
• how many coffees you produced with the individual beverage  
buttons,  
• how often cleaning, filter change and descaling programs  
were performed,  
15. CARE AND MAINTENANCE MESSAGES  
The machine will automatically display messages. In some cases  
the message allows you to continue to brew coffee. In other  
cases no further coffee brewing is possible before the task has  
been completed.  
• how close to the next tablet cleaning program, etc.  
PRESS RINSE  
14.9 DISPLAY SETTINGS (SETTING AM/PM / OZ)  
This function lets you select the time format AM/PM or 24HR  
format and the volume either in ounces OZ or milliliters ML.  
COFFEE READY  
• Push the Rotary Dial until the display shows MAINTENANCE.  
Turn the Dial until the display shows DISPLAY AM/PM / OZ.  
• Push and turn the Dial to change the time display and push  
the dial to confirm.  
Push the Rinse button (Fig. 2,E). The machine pumps hot water  
through the coffee spouts or continues a cleaning program.  
FILL SYSTEM / PRESS RINSE  
Place containers underneath the Auto Cappuccino System  
and the Hot Water Spout (Fig. 4) and push the Rinse button  
(chapter 6c).  
FILL WATER TANK  
The water tank is almost empty. Add water before resuming  
Turn Dial to change from OZ to ML and push to confirm.  
Turn the Dial to EXIT and push to return to COFFEE READY.  
brewing coffee.  
EMPTY GROUNDS or EMPTY TRAY  
The used coffee container is full (it holds a maximum of 16  
coffee portions). You must empty the coffee container before you  
29.  
can resume brewing coffee.  
It is time to decalcify the machine. You can still make coffee,  
Make sure the Dual Coffee Spouts are moved upwards. Carefully however we highly recommend to perform the decalcifying cycle  
lift and pull out the removable drawer (Fig. 18 and 19). TRAY  
MISSING. There is water in the drawer. Empty the drawer and  
the used coffee container, assemble and replace. Make sure the  
two metal contacts of the drawer are clean and dry.  
within the next few days (chapter 17.1).  
Please note: If you use the Clearyl cartridge and the message  
appears, then your cartridge function was not activated. Follow  
the instruction in chapter 13a to program and activate the  
cartridge. If the cartridge is already in use for several weeks  
Please note: If the machine is not used for a few days, pull out  
the tray and empty the used coffee container. Used, moist coffee install a new cartridge.  
grounds can develop mold and mildew.  
Important: If you pull out the drawer without any corresponding  
COFFEE READY / DECALCIFY NOW  
It is urgent to decalcify the machine.  
message in the display you must empty the used coffee container. COFFEE READY / CHANGE FILTER  
The machine assumes that it will be emptied. If you do not empty  
the container, used coffee will overflow inside the machine and  
cause serious damage to the coffee release mechanism.  
Please note: The machine does not sense if the used coffee  
container (Fig. 1,16) is inserted. If the used coffee container is  
not inserted, ground coffee discharges onto the drawer.  
TRAY MISSING  
It is time to replace the Clearyl filter (chapter 13b).  
NOT ENOUGH PRE-GROUND  
Not enough pre-ground coffee was filled into the ground coffee  
funnel (Fig. 1,11). The S9 OT stops the operation (chapter 9e).  
15.1 MANUAL MAINTENANCE CYCLES  
The S9 OT will display when it’s time to perform certain cleaning  
Insert the drawer with the empty used coffee container. Make sure programs. You can also manually access these programs and  
the metal contacts in the back of the drawer are clean and dry.  
perform them.  
FILL BEANS  
COFFEE READY.  
Add beans to the bean container.  
COFFEE READY / CLEAN MACHINE  
After approx. 220 coffee brewings or 80 initial rinsing cycles you  
must run a tablet cleaning cycle. You can still make coffee, how-  
ever we highly recommend to perform the cleaning cycle within  
the next few days (chapter 16.1).  
• Push the Rotary Dial until the display shows MAINTENANCE.  
• Push the Dial again, CLEAN CAPPUCCINO.  
Turning the dial shows you which programs you can access:  
CLEAN CAPPUCCINO (chapter 15.5)  
RINSE MACHINE (see example below in chapter 15.1)  
RINSE CAPPUCCINO (chapter 10g)  
COFFEE READY / CLEAN NOW  
CLEAN MACHINE (chapter 16.1)  
After 30 more coffee brewings the message reads CLEAN NOW. DECALCIFY MACHINE (chapter 17.1)  
COFFEE READY / DECALCIFY MACHINE CHANGE FILTER (chapter 13c)  
30.  
If you push the Rotary Dial to enter one of the above programs,  
the display guides you through the necessary steps.  
Please note: If the display shows MAINTENANCE and you do  
not select one of the above programs within five seconds, the  
S9 OT will return to COFFEE READY.  
• Turn the tool counter-clockwise slowly until the stone  
becomes loose.  
Attention: Do not try to turn the tool clockwise.  
• Fold the shield down and replace the screw.  
• Turn machine on and test the grinder without beans to see  
if the blockage has disappeared.  
Example:  
Run a manual hot water rinse cycle. COFFEE READY.  
• Push the Rotary Dial until the display shows MAINTENANCE.  
• Push the Dial again, CLEAN CAPPUCCINO.  
Turn the Dial until the display shows RINSE MACHINE.  
• Place a cup under the Dual Coffee Spouts.  
15.3 GENERAL CLEANING INSTRUCTIONS  
Never use abrasive materials or chemicals to clean the  
machine.  
• Clean the housing with a soft, damp cloth.  
• Rinse water tank daily and fill with fresh cold water.  
• Push the Rotary Dial. The S9 OT will push hot water through  
the Dual Coffee Spouts and then return to COFFEE READY.  
15.4 EMPTYING THE SYSTEM BEFORE TRANSPORT  
This procedure is necessary to prevent water and frost damage  
in case you intend to transport the machine.  
COFFEE READY  
• Place a container under the Cappuccino system and the Hot  
Water Spout.  
• Turn the machine off. The main power switch is still on.  
• Press and hold the Rinse button until the display shows  
SYSTEM EMPTYING  
• A small amount of water is dispensed. When the process is  
completed the machine turns itself off.  
15.2 REMOVING STONES FROM THE BURR GRINDER  
If the burr grinder is blocked, proceed as follows:  
Turn off the machine by pushing the ON/OFF button (Fig. 2,B).  
Wait until the machine has shut down completely.  
• Turn the main power switch off (Fig 1b).  
• Open the bean container lid and remove all beans (scoop out  
beans or use a hand-held vacuum cleaner).  
• Remove the screw in the bean container (Fig. 23) and  
push the grinder shield upwards (Fig. 24) Do not try to  
remove the shield completely.  
The next time the machine is turned on, the display shows  
FILL SYSTEM/PRESS STEAM (chapter 6c).  
• If any beans remain, remove them.  
• Attach the burr grinder release tool (in Welcome Pack) to the  
upper burr (Fig. 25).  
• If you cannot find this tool call 1-800-220-5701 and we will  
send the tool to you free of charge.  
15.5 CLEANING THE FROTHXPRESS  
After frothing a few drops of milk remain inside the frothXpress.  
The S9 OT displays RINSE CAPPUCCINO. Follow the instruc-  
tions in chapter 10g.  
31.  
If you use the frothXpress extensively or forgot to clean it, milk  
fat starts building up inside the frothXpress. In this case use the  
Cappuccino Cleaner liquid in the Welcome Pack.  
Run a CLEAN CAPPUCCINO cycle as follows:  
COFFEE READY.  
• Push the Rotary Dial until the display shows MAINTENANCE.  
• Push the Dial again, CLEAN CAPPUCCINO.  
• Push the Dial again. CLEANER FOR CAPPU. The Rinse  
button illuminates.  
• Remove the frothXpress from the steam nozzle.  
Take the frothXpress apart (Fig. 17a) and set the chrome plated  
face aside.  
• Place all parts other parts including the hose in a cup with  
warm water and add one cap-full (15 ml or 1/2oz.) of the  
cappuccino liquid.  
• Let sit for ten minutes or overnight.  
• Rinse all parts under fresh water and assemble.  
• Pour approx. 5 oz. of water into a container and add one  
capful (15 ml or 1/2oz.) of the Cappuccino Cleaner liquid.  
• Immerse one end of the long milk hose into the cleaning  
solution and insert the other end into the frothXpress. Turn  
the frothXpress Dial to the 12 o’clock position.  
• Place a container under the frothXpress (Fig. 4).  
• Push the rinse button. CAPPUCCINO CLEANS. The S9 OT  
siphons the cleaning solution through the frothXpress and  
stops automatically.  
• When the display shows WATER FOR CAPPUCCINO,  
remove both containers and empty. Fill fresh water into one  
container and insert the hose again. Place the other empty  
container under the frothXpress.  
16. AUTOMATIC CLEANING CYCLES  
16.1 CLEANING WITH SPECIAL TABLET  
The machine monitors how many coffees are brewed and how  
often the rinsing program is activated. After approx. 220 coffees  
the display shows COFFEE READY / CLEAN MACHINE. You  
can continue brewing coffee, however we highly recommend  
that you clean the machine as described below within the next  
few days. This cleaning program will remove oil build-ups in the  
brewing chamber. If the display shows CLEAN NOW clean the  
machine immediately.  
This cleaning program takes about 20 minutes. Please use the  
enclosed white cleaning tablet. The machine comes with a pack  
of 2 tablets. To re-order see chapter 20.  
Important: Once the cleaning program has started do not  
interrupt the procedure.  
• Push the Rinse button again. CAPPUCCINO CLEANS.  
The S9 OT will siphon fresh water through the frothXpress,  
removing the cleaning solution. COFFEE READY.  
• Squeeze the bottom of the venting tip (Fig. 17a) to make sure  
it is clean.  
COFFEE READY / CLEAN MACHINE  
1. Push the Rinse button. DURATION 20 MIN. / START YES.  
Please note: To clean the S9 OT at a later time, turn the Rotary  
Dial until the display shows START NO. Push the Rotary Dial to  
You can also immerse the frothXpress parts (except the chrome  
plated face) into a cappuccino cleaner solution as follows:  
32.  
exit the program. In this case the S9 OT will remind you with the  
message CLEAN MACHINE.  
2. Make sure that the water container is at least half full.  
Turn the dial until the display shows CLEAN MACHINE  
and push the dial. The display shows DURATION 20 MIN. /  
START YES.  
3. Push the Rinse Button. EMPTY TRAY.  
• Continue with the steps 2 through 9 from the chapter 16.1.  
4. Remove and empty the tray and the used coffee container  
and replace.  
17. DECALCIFYING  
Attention: If the tray and the used coffee container are  
already empty, you still need to remove the tray for approx.  
20 seconds and then replace it. PRESS RINSE.  
The machine has an integrated decalcifying program. This  
program takes 45 minutes. When the display shows COFFEE  
READY / DECALCIFY MACHINE it is time to decalcify the  
machine. The Rinse button is illuminated. You can still make  
coffee. However, it is highly recommended to decalcify the  
machine within the next 3 to 4 days.  
Please note: If you use the Clearyl water cartridge and the  
display shows DECALCIFY MACHINE then your cartridge  
function is not activated. Follow the instructions in chapter 13a  
to activate the Clearyl Cartridge. If the cartridge is in use for  
several weeks install a new cartridge.  
Important: The decalcifying program must not be interrupted.  
NOTE: Only use our special, square decalcifying tablets  
Model # 66281, see chapter 20.  
CAUTION: Never use vinegar or any other decalcifying agent.  
This might damage internal parts of the machine.  
CAUTION: Immediately remove any splashes of the decalcifying  
solution from sensitive surfaces, such as natural stone or wood.  
CAUTION: If the decalcifying solution comes in contact with the  
skin, rinse it off with water. If the solution comes in contact with  
your eyes, see a doctor.  
5. Place containers (20 oz.) under the coffee spout and the  
frothXpress (Fig. 4) and push the Rinse button (Fig. 2.E).  
The display shows CLEANS. After a short while you will hear  
a beep and the display shows ADD TABLET/PRESS RINSE.  
6. Open the ground coffee funnel lid and drop one white tablet  
into the opening (Fig. 22). Close lid.  
7. Push the Rinse button. The display shows CLEANS. The  
machine will start the automatic cleaning program by  
dispensing water in intervals into the containers underneath  
the spouts. When finished, the display shows EMPTY TRAY.  
8. Remove the tray. There will be water in the tray and in the  
used coffee container. Empty, clean and replace. The display  
shows COFFEE READY.  
9. Clean the ground coffee funnel. Remove the funnel and rinse  
under hot water and dry Replace funnel (Fig. 20 and 21).  
16.2 MANUAL TABLET CLEANING  
This program is useful if the brewing process slows down due to  
excessive oil build-up inside the machine. COFFEE READY.  
• Push and hold the Rotary Dial. MAINTENANCE.  
• Push the Rotary Dial, display shows CLEAN CAPPUCCINO.  
Important: Always wait until the decalcifying solution in the  
water tank has been used up. Do not fill additional decalcifying  
solution into the water tank.  
33.  
17.1 DECALCIFYING PROCEDURE  
COFFEE READY / DECALCIFY MACHINE  
1. Push the Rinse button until display shows  
11. Display shows RINSE WATER TANK / FILL WATER TANK.  
Remove the water tank, rinse thoroughly, fill it halfway with  
fresh water and replace. The display shows PRESS RINSE.  
12. Place containers under the auto cappuccino system and the  
hot water spout / coffee spouts (Fig. 4).  
DURATION 45 MIN. / START YES.  
Please note: To start at a later time, turn the Rotary Dial to  
START NO and push the Rotary Dial. The machine will still  
display COFFEE READY / DECALCIFY MACHINE.  
2. Push the Rinse button again, display shows EMPTY TRAY.  
3. Remove and empty the tray and the used coffee container  
and replace, display shows SOLVENT IN TANK.  
Attention: If the tray and the used coffee container are empty,  
you must remove the tray for approx. 20 seconds and then  
replace it.  
13. Push the Rinse button DECALCS.  
14. The machine pumps fresh water through the system and  
stops automatically. The display shows HEATING UP. When  
the display shows MACHINE RINSING, hot water will flow  
through the coffee spouts. EMPTY TRAY.  
15. Remove and empty the containers. Then carefully remove  
and empty the tray and the used coffee container and  
replace. COFFEE READY.  
4. Remove the frothXpress system from the Auto Cappuccino  
system (Fig. 16).  
The machine will automatically remind you when it’s time to  
decalcify again.  
5. Remove the water container and empty.  
6. Completely dissolve 3 of the large square decalcifying  
tablets in a container with 20 oz. of water (0.6 liters) and  
pour the solution into the water tank.  
17.2 MANUAL DECALCIFYING  
If you use very hard water it is possible that calcium builds up  
prematurely. If your coffee does not come out as hot as before  
it is a sign for calcium build-up. When this happens you can  
7. Replace water tank. SOLVENT IN TANK/PRESS RINSE  
8. Place containers under the Auto Cappuccino system and the manually start a decalcifying cycle as follows:  
hot water spout (Fig. 4).  
COFFEE READY  
9. Push the Rinse button. The display shows DECALCS and  
the light in the Rinse button flashes during the operation.  
The machine pumps the decalcifying solution in intervals  
through the Cappuccino system and the hot water spout.  
The display shows decalcifying status in the progress bar.  
10. When display shows EMPTY TRAY, remove and empty the  
containers. Then carefully remove and empty the tray and  
the used coffee container and replace.  
• Push the Rotary Dial until the display shows MAINTENANCE.  
• Push the Rotary Dial, display shows CLEAN CAPPUCCINO.  
Turn the dial until the display shows DECALCIFY MACHINE  
and push the dial. The display shows DURATION 45 MIN. /  
START YES.  
• Continue with the steps 2 through 15 from the chapter 17.1.  
34.  
18. TIPS FOR BETTER COFFEE  
machine for a minute.  
Height adjustable coffee-spout  
Adjust the height of the coffee-spout to the size of your cups.  
Turn machine on again. If the error message comes up again,  
try one more time.  
Grinding  
• If the message persists, call customer service.  
Please refer to chapter 7 "Adjusting the Grinder."  
Pre-warm cups  
TROUBLESHOOTING:  
Pre-warm cups in advance with hot water (chapter 9a).  
Sugar and cream  
Warmth is lost by stirring the contents of the cup. Adding milk  
or cream from the refrigerator considerably lowers the tempera-  
ture of the coffee.  
A. NO COFFEE COMES OUT OF THE COFFEE SPOUT  
Reason: Beans in bean container are not feeding properly into  
the grinder because they are stuck together.  
Solution: Stir beans before grinding and while grinding turn the  
grinding selector to the coarsest setting.  
When using very oily beans pour the beans onto a plate and let  
some of the sticky oils evaporate (this will not harm the aroma of  
the coffee).  
Reason: You used ground coffee in the ground coffee funnel.  
The ground coffee was too fine.  
19. ERROR MESSAGES / TROUBLESHOOTING  
ERROR MESSAGES:  
The machine can display any of the following error messages:  
ERROR 1, ERROR 3, ERROR 5  
Solution: Use ground coffee which is ground somewhat coarser.  
Reason: No water is transported through the system.  
Solution: Remove water container and make sure that the con-  
necting valve is free of any particles (like a coffee bean etc).  
Reason: The ground coffee funnel is clogged; the internal brew-  
ing chamber is clogged.  
Solution: Place a large cup underneath the coffee spout. Push  
the rinse button (Fig. 2E) a few times until the blocked coffee is  
removed. (Never fill more than 2 scoops of coffee in the ground  
coffee funnel; the funnel is not a storage area for ground coffee).  
Also, use a ground coffee which is ground somewhat coarser.  
Call our customer service hot line 1-800-220-5701.  
Your machine needs to be returned for service.  
ERROR 2, ERROR 4  
Your machine is too cold. The heating sensor does not react.  
Turn the machine off.  
• Keep the machine at normal room temperature (65º F or  
higher) for 2 hours .  
• Then turn it on again.  
If display still shows ERROR 2 or ERROR 4 call customer  
service.  
ERROR 6, ERROR 7, ERROR 8  
Turn machine off, turn the main power switch off and unplug  
35.  
B. THE DISPLAY READS "FILL WATER TANK" BUT THERE IS  
ENOUGH WATER IN THE WATER TANK.  
Reason: The floatation device (Fig.1,4) is stuck or missing.  
Solution: Clean the water container and make sure the floatation  
device moves freely.  
Solution: Within the water tank is a small compartment (like a  
mouse trap). Inside is a small black floatation device. On top is a  
small clear see-through plastic cover. This small plastic cover is  
missing and the floatation device is outside of the small com-  
partment. Check if you can find both pieces inside the water  
tank and put it back together. If you cannot find the pieces call  
1-800-220-5701. We will send the pieces FREE OF CHARGE.  
c. If any parts are missing call: 1-800-220-5701.  
D. GRINDER MAKES AN EXTREMELY LOUD NOISE;  
NO BEANS ARE GROUND  
Reason: A stone or object is blocking the burr grinder.  
Solution: See chapter 15.2.  
E. THE REMOVABLE DRAWER (Fig.1, 18) DOESN’T COME OUT  
Reason: The internal used coffee disposal chute did not retract.  
Solution: Turn off the machine. Wait a minute. Turn machine on  
and wait until it stops making any noise. Now try to pull out the  
drawer. If this does not work, turn the machine off. Now pull the  
drawer out with some force. You will feel some resistance. When  
the drawer is out you will see that the back wall of the used cof-  
fee container (Fig.1,16) is missing.  
C. INSUFFICIENT FROTHED MILK PRODUCTION  
Reason: Milk is initially not cold enough or your milk is not  
suited for thick frothing.  
Solution: Make sure milk is cold. Use a different type of milk.  
Skim milk will produce the thickest and longest lasting froth. Full  
fat milk will produce less thick froth.  
Reason: The components of the frothXpress are not assembled  
properly, or the components are clogged with hardened milk, or  
one or more of the components are missing.  
Reach into the machine and retrieve the back wall (it is a small  
black flexible piece). Set the used coffee container aside and  
insert the drawer (without the used coffee container) into the  
machine. Turn the machine on. Wait until all noise has stopped.  
The disposable chute should retract. Remove the drawer,  
replace the used coffee container and insert it back into the  
machine. Check if the drawer comes out easily.  
Solution:  
20. SUPPLIES  
a. Remove frothXpress. Check that steam comes out of the  
steam nozzle. Place a cup underneath the steam nozzle and  
use the milk function (chapter 10e). CAUTION: hot steam is  
dispensed from the steam nozzle.  
If no steam is released stop the milk function and use a  
needle to clear blockage inside the steam nozzle.  
b. Clean all frothXpress parts and assemble properly (chapter 15.5).  
The following supplies are necessary to keep your machine in  
good working order:  
Clearyl Water Filter Cartridge (one included).  
Model #64553; the machine will remind you automatically.  
Tip: If you brew 10 cups a day you need about one Clearyl  
cartridge per month. Always keep extra cartridges available.  
36.  
Special Cleaning Tablets (two included) Model #62205.  
Tip: If you brew 10 cups a day you need about one tablet  
every 3 weeks. Always keep extra tablets available.  
Auto-Cappuccino Cleaner (one bottle included).  
Model #63801  
Tip: If you use the auto cappuccino cleaner every other day  
you need a new bottle every 5 weeks.  
Decalcifying tablets (large square tablets) - Model #66281.  
Please note: You must use decalcifying tablets if you do not  
use the Clearyl cartridge.  
this warranty.  
In case the machine cannot be repaired, JURA-CAPRESSO will  
replace your machine with the same model with the same or less  
usage. In case we cannot replace your machine with the same  
model we will replace it with a model of the same or higher retail  
value with the same or less usage. Usage is defined by the  
number of coffees the machine has made when sent for repair.  
TRANSPORT: When sending the machine, use the original packing,  
the inner and outer cartons or use approximately 2” of bubble wrap  
and insert machine in a carton which will hold 40lbs.  
Any damage in transit is NOT covered by this warranty.  
THIS WARRANTY DOES NOT COVER:  
• Any machine NOT distributed by JURA-CAPRESSO within the  
United States.  
Any machine not purchased from an Authorized Jura-  
Capresso Dealer. (Call our customer service department to  
check for authorized dealers).  
You can order these supplies:  
• with the enclosed mail order form or  
• by calling our customer service center at 1-800-220-5701.  
21. LIMITED TWO-YEAR WARRANTY  
Please note: This warranty will be void if the Warranty / Product  
Registration has not been received two weeks after the purchase  
date (you can fax or mail the registration or you can register  
through our website www.capresso.com)  
This limited warranty covers your new Jura-Capresso  
S9 One-Touch Series for two years or up to 6,000 coffee  
brewings, whichever comes first.  
This warranty is in effect for the period and usage described  
above from the date of the first purchase and is limited to the  
United States of America. This warranty covers all defects in  
materials or workmanship (parts and labor) including free UPS  
ground transportation for both ways within the continental  
United States. For Hawaii and Alaska freight is not covered by  
• Any machine purchased through EBAY.  
• Damage caused by accident, abuse, negligence, misuse,  
• improper operation or failure to follow instructions contained in  
this manual.  
• Any service or alteration performed by an unauthorized person,  
company or association.  
• Damage caused by neglecting and omitting maintenance,  
cleaning and decalcifying cycles.  
• Damage caused by use of instant coffee or any other ingredients  
not allowed in this product.  
Other limitations and exclusions:  
Any implied warranties including fitness for use and merchantability  
are limited in duration to the period of the express warranty  
37.  
set forth above and no person is authorized to assume for  
JURA-CAPRESSO any other liability in connection with the  
sale of the machine. JURA-CAPRESSO expressly disclaims  
liability for incidental and consequential damages caused by  
the machine. The terms "incidental damages" refer to the loss  
of the original purchasers time, loss of the use of the machine  
or other costs relating to the care and custody of the machine.  
The terms "consequential damages" refer to the cost of repairing  
or replacing other property which is damaged when this machine  
does not work properly. Any loss of income is excluded. The  
remedies provided under this warranty are exclusive and in lieu  
of all others. This warranty gives you specific legal rights, and  
you may also have other rights which vary from state to state.  
22. FREE REPAIR SERVICE / EXTRA REPAIR COVERAGE  
Within the warranty period all repairs are free of charge including  
both ways UPS ground transportation to and from our service  
facilities within the continental United States.  
For Hawaii and Alaska freight is not covered by this warranty.  
In case the machine cannot be repaired, JURA-CAPRESSO will  
replace your machine with the same model with the same or less  
usage. In case we cannot replace your machine with the same  
model we will replace it with a model of the same or higher retail  
value with the same or less usage. Usage is defined by the  
number of coffees the machine has made when sent for repair.  
Within four weeks after your product registration you can  
purchase an extra 12 months of repair coverage. For details see  
the literature enclosed with this product.  
38.  
Jura-Capresso Inc.  
81 Ruckman Road, Closter, NJ 07624  
201-767-3999 • Fax: 201-767-9684  
Customer Service: 1-800-220-5701  

Nikon Cell Phone Accessories S1 User Manual
Motorola L6 GSM 900 MHz User Manual
Maxtor DIAMONDMAX 90432D3 User Manual
Kenwood KVT 526DVD User Manual
IBM DTLA 307045 User Manual
Hamilton Beach 44301 User Manual
Grindmaster 21 User Manual
GE Monogram DVLR223GG User Manual
Dell Computer Accessories 3448 User Manual
Cuisinart DCC 2900 User Manual