Cooper Lighting Computer Monitor 6109 User Manual

TROUBLESHOOTING  
If you have a problem with your Wall Switch, first follow this guide. If the problem persists, call the customer  
service hotline at 1-866-853-4293 between 8:00 AM and 7:00 PM ET weekdays.  
INSTALLING THE SWITCH  
ADJUSTMENTS  
LIGHT LEVEL  
TIME  
The length of time that the lights stay on is The sensor can be prevented from turning on lights when  
adjustable from 12 seconds to 30 minutes. there is already enough light in the room. Use a small  
• Use a small screw driver to set the time by screw driver to set the light level using this  
WARNING: Turn power off at the circuit breaker before wiring.  
6109  
SYMPTOM  
POSSIBLE CAUSE  
SYMPTOM  
POSSIBLE CAUSE  
• Remove the decorative coverplate (secured by two  
decorative screws).  
• Remove Control Cover (pinch the Control Cover at  
the indicated points and pull).  
• Remove the existing switch (if this is a retrofit  
application).  
• Connect the detector as shown in the diagram.  
Before installing the detector into the box, make  
sure there is no wire exposed at the connection.  
• Do not connect to neutral wire or damage to unit will  
occur.  
using the diagram below as a guide.  
diagram as a guide. In the fully clockwise position, the  
sensor turns on lights even in full daylight. In the fully  
counter-clockwise poition, the sensor only turns on lights  
when the surrounding light level is very low.  
Motion Sensing  
Wall Switch  
Light does not 1. Circuit breaker or fuse is turned  
Light does  
not turn off.  
1.  
2.  
Incorrect wiring.  
MODE switch is set to ON  
instead of AUTO.  
3. Motion is still present.  
4. Delay set by TIME control  
has not expired.  
come on.  
off.  
2. If the lamp being controlled has  
another switch, it may be turned  
off.  
To adjust the photocell:  
The 6109 Motion Sensing Wall Switch dectects motion to turn on  
lights for an adjustable amount of time. A built-in photo cell can be  
set to keep lights off when the lights aren't needed. The unit has  
excellent sensitivity and a wide 1800 detection range. It can be used  
with incandescent lighting as well as rapid start fluorescent lighting.  
Two LEDs allow for easy mode identification. (Not for use with elec-  
tronic ballasts)  
Dark (low  
light level)  
3. Bulb is defective.  
AUTO  
ON  
Any Light  
Level  
12 Sec.  
• When the light in the room is at  
the level you want the lights to  
turn on, set the switch to the  
AUTO position.  
AUTO LED  
AUTO  
ON  
4. LIGHT control is set too far  
toward the DARK position.  
5. MODE switch is set to OFF  
instead of AUTO.  
1. Heating or cooling ob-  
jects (such as air vents,  
appliances, or drafts through  
the wall box) are causing  
false triggering.  
Light comes  
on for no  
reason in  
the  
Pinch  
here  
Pinch  
here  
+
+
30 Min.  
• Put the TIME control to the 12  
sec. (fully counter-clockwise)  
position.  
6. Incorrect wiring.  
Auto mode.  
Lights do not  
stay on in the  
Auto mode.  
1. Motion has stopped in the room.  
TIME control is set for too short a  
2. delay.  
Installation is as easy as replacing a wall switch. However, some  
codes require installation by a qualified electrician.  
Switch on the sensor has  
2. been turned off and back on.  
• Put the LIGHT control to the mini-  
mum dark (fully counter-clock-  
wise) position.  
T I M E  
L I G H T  
There was  
a
momentary  
Features include:  
power interrup-tion. The light  
3. will turn off automatically  
when the "on" time expires.  
• Wait for the lights to turn off.  
• Turn the LIGHT adjustment clock-  
wise in very small steps and wait  
2 seconds before moving your  
hand in front of the sensor.  
Repeat until the lights controlled  
by the sensor come on. The light  
will now come on when the light  
level is at or below the present  
level and motion is detected.  
• 1800 motion detection angle  
• Adjustable on-time from 12 sec. to 30 min.  
• Adjustable photocell  
• Works with incandescent and rapid start fluorescent lighting (Not  
for use with electronic ballasts)  
• Works with motors up to 1/6 hp.  
• Push button selectable ON AND AUTO modes.  
Note:  
LOAD  
Adjustment screws  
found under (off-auto-  
on) face plate.  
BLACK  
(NEUTRAL)  
SPECIFICATIONS  
LIGHTING  
LOAD  
Control Cover  
Plate Removed  
to access  
Electrical input....................................................................................................................................120V, 60 Hz  
Fluorescent Load (not for electronic ballasts).....................(2) 30 Watt minimum 400 Watt maximum Rapid Start  
Motor Load........................................ ........................................................................................1/6 HP maximum  
Incandescent.............................................................................................................................500W at 120V AC  
On-Time...........................................................................................Adjustable approximately 12 sec. to 30 min.  
Photocell Sensor..........................................................................................From dull daylight to less than 1 FC.  
Coverage.............................................................................up to 20 ft. at 1800, up to 40 ft. in front of the sensor  
Dimensions .........................................................................................4.10 in. high, 1.7 in. wide and 2.00 in. deep  
Green ground wire to  
junction box screw or  
grounding wire  
Included are: • The sensor switch • Cover plate • 3 wire connectors • 2 large screws • 2 small screws.  
adjustments  
screws  
AUTO  
ON  
TIME  
LIGHT  
Complete Installation  
• Replace control panel cover and install the decorative wall plate. In installations where the Cooper motion  
sensor switch is combined with other switches or outlets on an expanded box, a combination wall plate will  
need to be purchased. Various combination wall plates are available at Home Centers and Electrical Supply  
Stores.  
40'  
INSTALLATION  
WARNING: For indoor use only.  
MODE  
Selection  
Switch  
BLACK  
HOT  
(LINE)  
SELECT A LOCATION  
NEW APPLICATION  
YOUR COOPER WIRING DEVICES ASSEMBLED PRODUCT TWO YEAR LIMITED WARRANTY  
• Press the push button a couple of times to make sure it operates freely.  
For a period of 2 years from the date of purchase, Cooper Wiring Devices will replace or repair the motion  
sensing switch provided that it has not been subject to abuse, improper installation or improper use, and is  
returned prepaid to Cooper Wiring Devices Quality Control Department at 203 Cooper Circle, Peachtree City,  
GA 30269. If the product has been discontinued, replacement will be made with the nearest available equiva-  
lent model. This warranty does not cover consumables (such as fuses). Proof of purchase in the form of a  
bill of sale or receipted invoice that shows that the item is within the applicable warranty period must be pre-  
sented to obtain the repair or replacement provided by the warranty. Repair or replacement as provided  
under this warranty is the exclusive remedy of the customer. Cooper Wiring Devices shall not be liable for  
any incidental or consequential damages for breach of any express or implied warranty on any of its prod-  
ucts. Except to the extent limited or prohibited by applicable law, any implied warranty of merchantability or  
fitness for a particular purpose on this product is limited in duration to the duration of this warranty. Some  
states do not allow the exclusion or limitation of incidental or consequential damages, or allow limitations on  
how long an implied warranty lasts, so the above limitations may not apply to you. This warranty gives you  
specific legal rights and you may also have other rights which vary from state to state.  
Choose a location where the motion sensor has a clear view of  
the entire area where occupant motion may occur.  
TYPICAL INSTALLATION  
USE  
MODE Selection Switch  
RETROFIT APPLICATION  
20'  
• Mount the detector into the wall box with the mounting screws.  
Motion sensing switch will replace existing wall switch. Use only  
where the existing switch location provides a clear view of the  
occupied area.  
• For test purposes, use a small screwdriver to turn the time control fully counter-clockwise  
and the light control fully clockwise. Turn the power back on at the circuit breaker.  
• Press MODE selection push button until the AUTO LED is on. Lamp will be on for 12 seconds. Allow two  
minutes for the unit to warm up. If motion is detected, the lights will turn on. The lights will turn off 12 sec-  
onds after motion is no longer detected.  
0'  
Pressing the pushbutton selects one of three modes of operation: ON, OFF, AUTO  
Typical Plan View of Coverage  
ON: Lights stay on continuously. The ON led is lit.  
GENERAL APPLICATION INFORMATION  
The detector is more sensitive to motion across the front of the sensor than to motion towards the sensor.  
OFF: Lights stay off. The AUTO led and the ON led are not lit.  
AUTO: Lights come on for time set when motion is detected and the light level is below the set level.  
The AUTO led is on and the ON led is off.  
The detector senses heat in motion and possible heat sources that change temperature quickly. Therefore, to  
avoid false triggering, avoid placing the sensor where it will be aimed at air conditioners, heaters, and other  
sources of heat or cold.  
Questions? Call 1-866-853-4293 8:00 AM to 7:00 PM Eastern Time, weekdays  
- 2 -  
*When in the OFF mode, the circuit is still alive. Turn off circuit breaker before re-lamping.  
 
598-1179-02 E  
- 4 -  
- 3 -  
469MX-PT  

Curtis Laptop LT7028 User Manual
Curtis Satellite TV System DVB350UK User Manual
Dimplex Electric Heater Duo400i Duo500i User Manual
Dimplex Water Heater DEE 1802 User Manual
Dukane Projector 8077A User Manual
Dynacord Stereo Amplifier LX1600 User Manual
Earlex Paint Sprayer HV3900 User Manual
Fisher Price High Chair T2684 User Manual
GBC Laminator H410 User Manual
GE Oven 164D2966P087 User Manual