Dual Speaker SBP10 User Manual

SBP10  
INSTALLATION/OWNER'S MANUAL  
 
SBP10 INSTALLATION  
Installation  
The following installation instructions are very basic. If you feel unsure about  
installing this speaker system yourself, Dual recommends aquiring the services  
of a professional car audio installation center.  
Before installation, please review the following guidelines:  
1. Be sure to carefully read and understand the instructions before  
attempting to install this product.  
2. For safety, disconnect the battery negative terminal prior to beginning  
the installation.  
3. If additional wiring is required, we recommend running all wires prior to  
mounting your speaker in place.  
4. To ensure reliable performance and minimize signal or power loss, use the  
highest quality connectors available.  
5. Use caution before you drill or cut! Be careful not to cut or drill into gas  
tanks, fuel lines, brake or hydraulic lines, vacuum lines or electrical  
wiring when working on any vehicle.  
6. Never run speaker wires underneath your vehicle. Running speaker wires  
inside the vehicle provides the best protection from exhaust, heat and  
environmental elements.  
7. Avoid running wires over, near or through sharp-edged surfaces. We  
suggest you also use rubber grommets to protect any wires routed  
through metal, especially the firewall.  
8. When running the speaker cable from the amplifier, avoid running it near  
sources of high current (i.e. wiring harnesses, battery cables).  
9. When connecting the amp, the positive (+) speaker output from the bass amp  
connects to the positive (+) terminal and the negative output (-) connects  
to the negative (-) input terminal on the input cup located on the rear of  
the subwoofer enclosure. DO NOT CONNECT AMP OR ANY AUDIO SOURCE TO  
ILLUMINATION INPUTS, AS DAMAGE TO LIGHTS WILL OCCUR.  
10. For the illumination connection, the positive (+) output from your 12V system  
connects to the positive (+) input and the negative (ground) connects to  
the negative (-) input on the input cup located on the rear of the subwoofer  
enclosure. Improper 12V polarity will not cause damage to the lights, but they  
will not illuminate.  
3
 
SBP10 INSTALLATION  
Enclosure Guidelines  
To achieve the best possible sound from this subwoofer enclosure, Dual  
recommends aquiring the services of a professional car audio installation center.  
If you feel confident in your ability to install this product without the assistance of  
a professional, please read this section thoroughly. We have provided a number  
of placement recommendations and installation tips to assist you. Keep in mind  
that these are provided as a guideline and you may find that other placements  
may provide better results for your specific vehicle.  
• Make sure all moving parts and factory electrical wires are out of the way and  
will not interfere after installation.  
• Ensure the wire is of sufficient length to avoid pulling or stretching. This is even  
more important if the wires will be run under or through the factory interior.  
• Use electrical tape and wire ties to ensure all wires are properly secured.  
• Avoid installing speakers or electronics where they can be subject to moisture.  
• Ensure the speaker wires are connected using correct polarity. The positive  
polarity is marked by a (+) sign. Incorrectly connected subwoofers will result in  
limited bass output.  
• Ensure the Illuminite wires (12V) are connected using correct polarity. Do not  
connect an amplifier or any audio output source to the Illuminite inputs, as  
doing so will cause permanent damage to the lighting elements.  
• Speaker wire should be isolated from the vehicle’s electrical system to avoid  
noise being picked up by the amplifiers.  
• We recommend using 14 gauge or larger sized speaker wire to ensure your  
subwoofer receives the full power output of your amplifier.  
• Remember to listen responsibly and respect your ears. Being exposed to  
sounds over 125dB for even short periods of time can create permanent  
hearing loss!  
4
 
SBP10 INSTALLATION  
Illuminite™ Lighting Hook-Up  
Dual’s patent-pending Illuminite bulb system and control circuitry provide for  
extraordinary blue illumination, allowing for creative, color-coordinated  
installations. The interior of your vehicle will never sound or look ordinary again!  
Let your imagination take you there.  
The lighting features of all Illuminite products require a 12V power source to  
operate. The speaker has two distinct sets of input terminals. The first is labeled  
"audio input" and the second is labeled "Illuminite lighting inputs". The inputs are  
clearly marked with a label positioned directly above the terminal housing. The  
polarity (+ and -) indicators for each set of inputs also appear on these labels.  
1. Do not connect your amplifier or any audio source to the Illuminite inputs.  
These inputs are designed for switched 12V DC power only. Do not connect  
directly to your battery permanently, as it will cause your battery to discharge.  
Please use a switched 12V source.  
2. See Fig. 1a, (illustrated wiring diagram) to be sure to maintain polarity. Be  
sure to connect to a switched 12 volt source. Proper connection would be  
the positive (+) 12V wire to the positive (+) Illuminite input terminal and the  
negative (-) Illuminite input terminal to a solid chassis ground.  
DO NOT CONNECT AMP OR ANY AUDIO SOURCE TO ILLUMINATION INPUTS.  
DAMAGE TO LIGHTS WILL OCCUR, AND WARRANTY WILL BE VOID!  
Fig 1a  
Lighting Hook-Up From Rear  
From Amplifier  
12 volt DC source  
Ground  
Illuminite Lighting  
Input Terminals  
Audio Input Terminals  
Note: The SBP10 Illuminite lights are not removable. There are no serviceable  
parts inside or attached to the speaker assembly. The SBP10 is a sensitive  
electronic device. Removal of or tampering with any part of the speaker and/or its  
assemblies will damage the product and void the warranty.  
5
 
SBP10 GENERAL FEATURES  
General Features  
• Input Terminal Cup  
The input terminal cups provide a quick and easy connection from your  
amplifier to the enclosure, and 12 volt inputs to power the Illuminite feature.  
• Computer-Tuned Acoustic Chamber  
Dual’s enclosures utilize a specialized tuned-port, computer-aided design to  
increase output efficiency.  
• Low Q Optimized Subwoofer  
This subwoofer is designed to create loud yet very accurate bass.  
• Curved Plexiglas Viewing Window  
• Extremely Durable Carpeted Enclosure  
• Nailed and Glued Construction with Added Bracing  
This construction eliminates enclosure movement caused by high sound  
pressure levels.  
• In-Line LED Protection Circuitry  
• On-Off Illuminite Toggle Switch  
• Removable Illuminite Logo  
This static poly logo can be placed on any window or glass surface.  
6
 
SBP10 WARRANTY  
Limited One-Year Warranty  
This warranty gives you specific legal rights. You may  
What to do?  
also have other rights which vary from state to state.  
1. Before you call for service, check the  
troubleshooting guide in your owner’s manual. A  
slight adjustment of any custom controls may save  
you a service call.  
Dual Electronics Corp. warrants this product to the  
original purchaser to be free from defects in material  
and workmanship for a period of one year from the  
date of the original purchase.  
2. If you require service during the warranty period,  
you must carefully pack the product (preferably  
in the original package) and ship it by prepaid  
transportation with a copy of the original receipt  
from the retailer to an  
Dual Electronics Corp. agrees, at our option, during  
the warranty period, to repair any defect in material  
or workmanship or to furnish an equal new, renewed  
or comparable product (whichever is deemed  
necessary) in exchange without charges, subject to  
verification of the defect or malfunction and proof  
of the date of purchase. Subsequent replacement  
products are warranted for the balance of the original  
warranty period.  
authorized service center.  
3. Please describe your problem in writing and  
include your name, a return UPS shipping address  
(P.O. Box not acceptable), and a  
daytime phone number with your shipment.  
Who is covered? This warranty is extended to the  
original retail purchaser for products  
purchased and used in the U.S.A.  
4. For more information and for the location of the  
nearest authorized service center please contact  
us by one of the following methods:  
What is covered? This warranty covers all defects  
in material and workmanship in this product. The  
following are not covered:  
• Call us toll-free at 1-866-382-5476  
• E-mail us at [email protected]  
installation/removal costs, damage resulting  
from accident, misuse, abuse, neglect, product  
modification, improper installation, incorrect line  
voltage, unauthorized repair or failure to follow  
instructions supplied with the product, or damage  
occurring during return shipment of the product.  
Exclusion of Certain Damages: This warranty is  
exclusive and in lieu of any and all other warranties,  
expressed or implied, including without limitation  
the implied warranties of merchantability and fitness  
for a particular purpose and any obligation, liability,  
right, claim or remedy in contract or tort, whether or  
not arising from the company’s negligence, actual or  
imputed. No person or representative is authorized  
to assume for the company any other liability in  
connection with the sale of this product. In no event  
shall the company be liable for indirect, incidental or  
consequential damages.  
7
 
Dual Electronics Corp.  
Toll Free: 1-866-382-5476  
©2008 Dual Electronics Corp. All rights reserved.  
NSA0608-V01  
 

Craftsman Air Compressor 921166390 User Manual
Crock Pot Slow Cooker SC7500 User Manual
Cuisinart Coffeemaker 73289 User Manual
Dukane Projector 8763 User Manual
Electro Voice Portable Speaker PIM 222 User Manual
Electro Voice Speaker System FRi 122 85 User Manual
Faber Ventilation Hood INCA PRO 38 RB User Manual
Frigidaire Cooktop 318200633 User Manual
Fujitsu Universal Remote N6B 0558 B70 User Manual
Garland Range C0836 1 User Manual