GE Vacuum Cleaner RPS12 User Manual

Catalog Number: RSP12  
Total Lighting Control  
Remote Control Smart Sweeper  
DESCRIPTION  
RED  
MASTER  
R
L
ACC.  
24VRECT  
BLUE  
POWER  
BLACK  
RED  
24VAC  
RED  
The Remote Control Smart Sweeper is an intelligent  
component for simple lighting control. It provides 12  
individual switch inputs and one Master input for a group  
of 12 relays. Each input will accept any 2- or 3-wire  
switch. The RSP12 converts any switch input to a  
momentary output to drive the corresponding relay(s).  
Each output can drive up to three relays in parallel.  
WHITE  
RED  
REV 0  
HORTON CONTROLS COPYRIGHT
BLACK Y  
BLACK  
WHITE  
S
W
T
1
BLACK  
437D687  
BLUE  
RSP12  
1 WHITE  
RED  
R
L
RED  
S
BLACK  
W
BLACK Y  
2
BLUE  
T
2 WHITE  
RED  
S
BLACK  
W
T
3 WHITE  
The RSP12 also provides several advanced functions for  
basic lighting automation. Besides the Master ON/OFF  
function, it allows options for Time Delay and Flick  
Warning for individual overrides, as well as Automatic  
ON for all lights.  
RED  
S
BLACK  
W
E  
T
4 WHITE  
MASTER SWITCH
Y PWR  
ACCESSOR  
24V RECT  
INPUT  
POWER INPUT  
AC  
RED  
S
BLACK  
W
24V  
T
otal Lighting Control  
GE T  
RSP12  
Catalog Number  
Description  
Remote Control Smart Sweeper  
Converts 2- or 3-wire switch inputs to momentar  
Each switch input drives corresponding relay output.  
Master Switch controls all 12 outputs.  
5 WHITE  
The RSP12 should be installed in a lighting automation  
panel or an accessory cabinet as detailed on the  
following page.  
RED  
S
BLACK  
W
y outputs.  
T
1
SWITCHINPUT  
6 WHITE  
Installation  
AC power to Power Input.  
Wire 24V  
RED  
S
Connect up to 3 relays to each Relay Output.  
Wire any 2- or 3- wire switch to Switch Inputs, including  
Master Switch, if desired.  
BLACK  
W
T
7 WHITE  
FEATURES  
Close contact during normal working hours.  
Occupied –  
Opening contact turns OFF all relays and enables time delays.  
ime Delay –  
• T  
to 8=2 hrs. 9=1 min. test). After "occupied" hours, any  
relays manually switched ON will automatically turn OFF  
Set dial in 15-minute increments (1=15min.
RED  
S
• 12 individual relay outputs, with up to 3 relays wired  
in parallel per output.  
after the set amount of time.  
arn –  
• W  
BLACK  
W
Lights "flick" 5-minutes before turning OFF at  
).  
NO  
or  
YES  
end of day or time delay (  
T
).  
NO  
8 WHITE  
Lights turn ON automatically at start of normal  
Auto On –  
working hours (  
LISTED 533F  
) or require manual switch ON (  
YES  
• 12 individual switch inputs (one per relay) and one  
Master input.  
vice: 1-800-884-4852  
Ser  
RED  
S
ENERGY MANAGEMENT  
EQUIPMENT SUBASSEMBL  
Y
R
Made in U.S.A.
BLACK  
W
GE Wiring Devices  
wick, RI  
T
ar  
W
• Inputs accept any 2- or 3-wire switch (dry contact).  
• Master ON/OFF control for group of relays while  
retaining individual switch override.  
Additional control of subgroups by tying any  
combination of inputs together.  
9 WHITE  
RED  
S
WBLACK  
T
1
WHITE  
0
L
Y
1
1
BLACK  
BLUE  
RED  
S
WBLACK  
• “Occupied” contact to indicate normal working hours.  
Option to turn lights on automatically at start of  
normal working hours.  
Time delay in 15-minute increments up to 2 hours.  
Option to “flick warn” occupants 5 minutes before  
lights go off.  
T
1
RED  
WHITE  
1
R
L
Y
1
2
AUTO ON  
YES  
BLACK  
BLUE  
RED  
WARN  
S
TIME DELAY  
2
1
YES  
NO  
W
O
N
T BLACK  
NO  
0
OCCUPIED  
BLACK  
1
2
WHITE  
RED  
ASM 437D688G  
Before starting, read the installation instructions inside.  
If you have questions call GE Service at:  
1-877-584-2685 (USA) or 1-800-661-6619 (Canada)  
Installation Instructions  
IMRSP12  
 
Catalog Number: RSP12  
CAUTION: The power supply must be OFF when  
inserting or removing components. These instructions  
assume the panel has a standard cover which exposes  
both line-voltage and low-voltage sections. The line-  
voltage sections must be covered to avoid exposure to  
live high-voltage wiring.  
INSTALLATION  
There are two recommended ways to install the RSP12  
Remote Control Smart Sweeper — in a Lighting  
Automation Panel (LAP) or in an Accessory Cabinet near  
a Lighting Automation Panel  
18/2 AWG  
2.  
WIRE  
24 VOLT  
RECTIFIED  
POWER  
24V  
24V  
PILOT  
COMMON  
YELLOW  
RECT  
BLUE  
RECT  
BLUE  
Installation in a Lighting Automation Panel  
24VRECT ACC  
BLUE WHITE  
24VAC COM  
A complete LAP assembly includes the following TLC  
components:  
RSP12  
Tub  
RTUB12, -24 or -48  
Cover  
Interior  
RCOV12xx, -24xxx or -48xxx  
RINTER0012RC, -0024RC or -0048RC*  
ON TLC PANEL  
MOTHERBOARD  
Power Supply RPWRxxx  
Relays  
RR7P or RR9P  
LOAD  
* RINTER0012RC and -0024RC accept one RSP12, RINTER0048RC accepts one or two  
RED BLACK YELLOW WHITE  
1
Details for assembling a complete Lighting Automation  
Panel are outlined separately in the RINTER installation  
instructions. Once the panel is assembled and relays are  
connected to the motherboard, the RSP12 may be  
installed.  
CIRCUIT  
RRxP RELAY  
ON TLC PANEL  
MOTHERBOARD  
20/2 AWG  
RED  
BLACK  
BLUE  
3.  
WIRE  
Basic Installation Steps  
RELAYS  
RSP12  
1. Mount the RSP12(s) on the panel accessory bracket.  
2. Wire 24V rectified power from the panel motherboard  
to the blue and white power input tabs on the RSP12.  
3. Wire red and black connections for each relay from  
the panel motherboard to relay outputs on the RSP12.  
4. Wire any 2- or 3-wire switch to the individual switch  
inputs and/or the Master switch input on the RSP12  
(not on the panel motherboard).  
4. WIRE ANY 2- OR 3-WIRE SWITCHES  
20/2 AWG 1000 FT. MAX.  
RED  
BLACK  
WHITE  
RED  
5. Select additional control functions.  
JUMP RED TO BLACK  
MAINTAINED  
BLACK  
WHITE  
ISOLATED  
CONTACT  
Installation in an Accessory Cabinet near the LAP  
RED  
BLACK  
WHITE  
20/2 AWG 1000 FT. MAX.  
JUMP BLACK TO WHITE  
Accessory cabinets with covers include:  
RED  
BLACK  
WHITE  
RBS1  
RBS2  
Accepts one (1) RSP12  
Accepts two (2) RSP12s  
RED  
BLACK  
WHITE  
2-WIRE  
MOMENTARY  
PUSH BUTTON  
Mount the RSP12 in the accessory cabinet and wire the  
same as above.  
RED  
BLACK  
WHITE  
20/3 AWG 1000 FT. MAX.  
RSP12  
RED  
BLACK  
WHITE  
RED  
BLACK  
WHITE  
STANDARD  
3-WIRE  
MOMENTARY  
RED  
BLACK  
WHITE  
20/3 AWG 1000 FT. MAX.  
RED  
12-RELAY  
LIGHTING  
BLACK  
WHITE  
AUTOMATION  
PANEL  
24-RELAY LIGHTING  
AUTOMATION PANEL  
RED  
BLACK  
WHITE  
STANDARD  
3-WIRE  
MAINTAINED  
RED  
BLACK  
WHITE  
48-RELAY LIGHTING  
AUTOMATION PANEL  
1. MOUNT RSP12 IN PANEL  
 
Catalog Number: RSP12  
EMERGENCY SERVICE OR SUPPORT:  
1-877-584-2685 (USA) or 1-800-661-6619 (Canada)  
ADDITIONAL CONTROL FUNCTIONS  
Four optional control functions are available at the  
bottom of the RSP12 board: Occupied, Time Delay, Warn  
and Auto Off. Set these functions for all relays connected  
to the RSP12 as a group, based on the needs at the site.  
RSP12  
WARN  
YES  
AUTO ON  
YES  
NO  
0
OCCUPIED  
RD WHTE  
NO  
Occupied  
20/2 AWG 1000 FT. MAX.  
The Occupied contact is available for connection with a  
timeclock or building automation system. It indicates  
when the building is operating under normal working  
hours (CLOSED contact) or after hours (OPEN contact).  
Properly connecting and scheduling the Occupied  
contact determines when other functions will be enabled.  
MAINTAINED ISOLATED CONTACT  
IN TIME CLOCK (BY OTHERS)  
OCCUPIED CONTACT  
Time Delay  
RSP12  
If the Time Delay function is set, when an occupant turns  
on a switch after hours (Occupied contact OPEN), the  
RSP12 will turn off the lights again after a predetermined  
amount of time. Each occupant override will have its own  
time delay.  
WARN  
YES  
NO  
AUTO ON  
YES  
N
0
OCCUPIED  
RED WHITE  
0
TIME DELAY  
0 = NO TIME DELAY  
1 = 15-MINUTE DELAY  
2 = 30-MINUTE DELAY  
3 = 45-MINUTE DELAY  
ETC. TO…  
8 = 2-HOUR DELAY  
9 = 1-MINUTE TEST  
Set the Time Delay dial as follows:  
0
No time delay (no automatic off; lights must be  
manually turned off)  
1-8 15-minute to 2-hour delay, in 15-minute  
increments  
9
1-minute test  
RSP12  
WARN  
YES  
NO  
AUTO ON  
YES  
NO  
Warn  
0
CCUPIED  
WHITE  
When the RSP12 turns relays OFF (at the end of normal  
working hours, or at the end of a time delay), it will  
optionally warn the occupants by blinking the lights five  
minutes before they go off.  
WARN  
YES  
NO  
1
O
N
WARN SWITCH  
Set the WARN switch to YES or NO as follows:  
YES Gives a 5-minute warning before lights turn off  
NO Turns lights off without giving the warning  
Auto On  
RSP12  
When the Occupied contact closes at the start of normal  
working hours, the RSP12 can optionally turn all the  
relays ON automatically.  
WARN  
YES  
NO  
AUTO ON  
YES  
NO  
0
CCUPIED  
WHITE  
Set the AUTO ON switch to YES or NO as follows:  
AUTO ON  
YES  
NO  
2
YES Automatically turns all relays ON at start of  
normal working hours  
NO Manual switch required to turn relays ON  
AUTO ON SWITCH  
GE Lighting Controls, 41 Woodford Ave., Plainville, CT 06062  
Made in U.S.A.  
 

Cisco Systems Network Router 2821 Series User Manual
Creative MP3 Player NOMAD Zen XTRA User Manual
Curtis TV DVD Combo TVD2000 User Manual
Dimplex Fan BFH24T User Manual
Dual Portable DVD Player XDVD8285 User Manual
Dual Portable Multimedia Player XDVD210 User Manual
Dynex Network Router DX E402 User Manual
Electro Voice Microphone RE90B BW User Manual
GE Monogram Ventilation Hood ZV830SM User Manual
Glen Dimplex Home Appliances Ltd Cooktop GT 755 User Manual